Start the water flowing by turning off the water intake valve at the tank and turning on a hot-water faucet.
要使用热水槽里的水,首先确保电或天然气已经关掉,在槽的底部把管子打开,通过关掉槽里的进水阀,打开热水水龙头,让水开始流出来。
Open the "hot out" valve and let the tank start to fill. It will take probably about 5-10 minutes or so to get 45 gallons into the tank.
当我们打开热水出水阀,水会自然地流入水箱,只要5至10分钟左右,水箱内就能添加45加仑水。
Press the "Start" button, the pump running, then open the suction valve of the pump.
按下水泵“开”按钮,泵即运转;然后打开泵的吸入阀。
Reciprocating pump discharge pipe must be before the start of the valve to open.
往复泵启动前必须将排出管路中的阀门打开。
Students start running smoothly machine refrigerant low offset normal value please press following methods to adjust hot gas bypass valve.
机台启动运行平稳后冷媒低压偏移正常值时请按如下方法调节热气旁路阀。
When you get back to the valve stem you start with the second spoke from the valve stem and continue the same way, and on the third pass you start with the third spoke from the valve stem.
当您回到您启动阀杆与第二阀杆上发表演讲,并继续以同样的方式,并在第三关你的第三个开始从阀杆发言。
Start the bilge water feed pump, check the feed water solenoid valve and flow switch.
启动舱底水供给泵,检查补水电磁阀和流量开关是否工作。
In general, a foot valve can be mounted if the pump is mounted above the water level of the water inlet so as to start the pump with priming, it can also use the way of vacuum pump water leading.
如水泵安装在进水水位以上时,为了灌泵启动,一般可装底阀,也可采用真空泵引水的方法。
Adopt gas fire extinguishing controller to collect signal to start the solenoid valve, the action is stable and reliable, reflect sensitively.
采用气体灭火控制器收集探测元件探测的信号来启动电磁阀,动作稳定可靠、反应灵敏。
The industrial used valve massive applications, will be later only then start from the watt invention steam engine.
工业用阀门的大量应用,是从瓦特发明蒸汽机以后才开始的。
Should be fully open before the start of suction and discharge pipe valves, non-closing valve started.
启动前应全开吸入和排出管路中的阀门,严禁闭阀启动。
The principle of it is:When the upper level is reached, the rotary valve and bin gate will start in turn to discharge.
其控制原理为:当上料位信号出现时,卸灰电机、闸板阀开始工作,进行排灰。
Should be fully open before the start of the suction and discharge pipe valves, non-closing valve to start.
启动前应全开吸入和排出管路中的阀门,严禁闭阀启动。
Intensification logic valve start is directly controlled by pilot valve without any intermediate links, so the building-up time of intensification is fully guaranteed.
增压逻辑阀的开启直接由先导阀控制,不经过任何中间环节,使得建压时间得以充分保证。
A dynamic simulation model of start-up process including fuel pumped section and the dynamic nozzle valve lever, etc. is established for the torpedo thermal power system with pressure adjustment mode.
文中针对使用燃料压力调节供应方式的热动力系统,建立了包括充填集液腔和喷嘴阀杆运动等启动过程动态仿真模型;
Intake system has electric heaters and temperature control the intake valve, you can ensure that a smooth start and shorten the warm-up time.
进气系统有电加热器和温度控制进气阀,可以确保汽车顺利启动和缩短暖机时间。
Vacuum pump's start order is: First turns on the driving fluid valve, pours into the driving fluid to the pump, then the starting motor, turns on the inspiration pipeline once more, normal work;
真空泵的启动顺序为:首先打开工作液阀门,向泵内注入工作液,然后启动电动机,再次打开吸气管路,正常工作;
I. To disconnect the fixed CO2 start up line (include in fire station) and to close CO2 discharge valve to engine room.
拆下大型固定CO2的启动瓶控制管路(包括消防站的),关闭CO2到机舱的释放阀,将CO2的门电焊焊死。
All kinds of resisting moment effects upon pump start-up process are fully considered and the different operational results of outlet gate with little flap valve are also reviewed.
在计算过程中,比较完整地考虑了各种阻力矩对起动过程的影响,同时重点考察了平直管出水流道,具有快速闸门带小拍门断流装置形式的起动效果。
Open piping attached to a filled tank will not start to drip-leak following installation and test of a Chemtrol Tru-Bloc shut-off valve.
在ChemtrolTru-Bloc关闭阀安装和测试后,连接到满储的储罐的管道开口将不会开始滴漏。
In accordance with our system to start flow control valve selection description.
我们按照系统流程来展开控制阀选用说明。
The ECU accomplishes the fast energizing of the solenoid valve by driving circuit with high frequency PWM, and detects the start of injection by the differential signal of driving current.
采用高频脉宽调制功率驱动电路进行电磁阀的高速强力驱动,并利用电流微分信号有效反馈了控制阀关闭始点。
A tire tool or flat stock can be used to pry one part of the bead up over the rim flange (start near the valve stem).
可用轮胎工具或扁平的撬棒把轮缘的一端从轮辋辋圈上撬起。
A tire tool or flat stock can be used to pry one part of the bead up over the rim flange (start near the valve stem).
可用轮胎工具或扁平的撬棒把轮缘的一端从轮辋辋圈上撬起。
应用推荐