锥度是指圆锥的底面直径与锥体高度之比,如果是圆台,则为上、下两底圆的直径差与锥台高度之比值。锥度塞规主要用于检验产品的大径、锥度和接触率,属于专用综合检具。锥度塞规可分为尺寸塞规和涂色塞规两种。由于涂色锥度塞规的设计和检测都比较简单,故在工件测量中得到普遍使用。
炼钢连铸系统结晶器铜板锥度误差大问题研究_建筑施工论文 关键词结晶器 锥度 传感器 [gap=333]Key words mould taper sensor
基于1156个网页-相关网页
产品型号(Model):ISO30-ER32-60L 刀柄锥度(ToolholderTaper): 19小时 供应一体式钻夹头刀柄BT40-APU13-110自紧夹头刀
基于60个网页-相关网页
拔模锥度 draft taper ; draft
锥度车削 taper turning
主轴锥度 Spindle taper ; Taper of spindle ; Taper in Spindle Nose ; Spindle Conicity
主轴孔锥度 Spindle taper ; Taper hole of spindle ; Mores ; Spindle hole taper
莫氏锥度量规 morse taper gauge ; morse taper gauguste
锥度量规 [机] cone gauge ; taper gage
锥度规 taper gauge ; conical gauge
标准深锥度 Standard depthwise taper
This system can cut the object not only at large taper but also for top bottom different shape.
本系统不仅能进行大锥度的切割,而且能够进行上下异形体的切割。
参考来源 - 大锥度电火花线切割机数控系统的设计Considering the difficulty of traditional process in drawing muti-slope cone-box shaped parts in one operation, hydroforming process is adopted and the combination of numerical simulation and experimental research are carried out.
针对传统工艺拉深具有不同锥度侧壁的锥盒形件难以一次成形的特点,本文提出了利用液压成形工艺,采用数值模拟与实验研究相结合,对具有不同锥度侧壁的锥盒形件的成形进行研究。
参考来源 - 具有不同锥度侧壁的浅锥盒形件液压成形的数值模拟与实验研究The results implied that the primary stability decreased with implant taper increasing.
结果提示,锥度变化能够影响即刻负载牙种植体的初期稳定性,随着锥度增加,种植体的初期稳定性降低。
参考来源 - 外形设计对即刻负载牙种植体初期稳定性影响的三维有限元研究The stress concentration will be the minimum when the cone angle is in the range of 2° to 10°.
计算结果表明:锥度控制在2°~10°之间,接头中的应力集中最小。
参考来源 - C/SiC复合材料连接接头应力与破坏形式数值分析The machine can measure following parameters: radical force variation, lateral force variation, conicity and so on. The product accord with development of our national tyre manufacturing is an important national industrialization item.
它用于测量轮胎负荷受载下的径向力波动、侧向力波动、锥度等,产品符合国家的发展方向,是国家重点研究的产业化项目。
参考来源 - 轮胎均匀性参数测量方法的研究·2,447,543篇论文数据,部分数据来源于NoteExpress
您还将了解锥度对象、圆角选项和斜角功能的使用。
You will also learn about the use of the Taper object, Fillet option and Bevel function.
锥度:任何轴承部件的表面角度不正确或者不符合图纸要求。
TAPER: any surface of any bearing part that is not the correct Angle or not to print.
锥度研磨:研磨锥度表面的工艺,很大程度上依赖于蓝图的设计规范。
TAPER GRIND: Grinding process which produces angled surfaces, may be intentional or unintentional depending on blueprint specifications.
应用推荐