5输入轴的热处理质量不合格。
在主减速器动力输入轴上设装光电脉冲器；
The power input shaft of the main speed reducer is provided with an optoelectronic pulser;
从动盘的旋转带动变速器输入轴随之转动。
当获取输入轴，该轴带有最大绝对值将被返回。
When getting the input axis, the axis with the largest absolute value will be returned.
其输入轴与变速器的输出轴用万向传动装置连接。
Its input axis and transmission gearbox's output shaft with the rotary transmission device connection.
说明：当输入轴旋转方向改变，输出轴相应改变。
Specification: direction of rotation of output shaft varies with that of input shaft.
这种联轴节的输入轴与输出轴成空间交错轴关系。
The input shaft and output shaft of this kind of double universal couplings are non-parallel, non-intersecting.
调节油缸的长度，改变输入轴和输出轴间的传动比。
The transmission ratio of the input shaft and the output shaft can be changed by regulating the length of the oil cylinder.
然而，更大的车轮从冠轴输入轴轴线位移，机械效率降低。
However, the greater the displacement of the input shaft axis from the crown wheel axis, the lower the mechanical efficiency.
齿轮段也有输入轴和输出轴，它必须吧动力传递给驱动轮。
The gear section also has the input shaft and the output shaft needed to transmit power to the drive wheels.
输入轴上的滚柱轴承最低l 10使用寿命为10万小时。
Roller bearings on the input shaft with a minimum of 100,000 hours L10 bearing life.
价格低廉，精密钻孔轴，平坦安装，悬臂式负载能力输入轴。
Extremely low cost. Standard high-precision ground spindle. Standard flat mounting arrangement. High overhung load capacity input shaft.
输入方式：电机直联、电机皮带联接或输入轴、联接法兰输入。
Input Method: electrical Direct, electrical connection, or a belt input shaft, flange type connection.
泵轮的旋转作用冲击液体，液体的作用推动涡轮旋转变速器输入轴。
The rotating action of the pump against the fluid and the action of the fluid against the turbine turn the transmission input shaft.
万向节机构的输入轴和输出轴的夹角是影响泵性能的一个关键参数。
The crossing Angle between the driving shaft and the driven shaft is a key parameter that affects the performance of the pump.
在这样情况下方位陀螺的输入轴是处于垂直位置，同时摆锤单元在零位。
The input axis of the azimuth gyro under this condition is vertical, and pendulum unit is nulled.
一种微耕机全齿轮传动装置，包括传动箱体、传动输入轴和传动输出 轴；
The utility model relates to a full gear driving device for a micro tilling machine, which comprises a driving box body, a driving input shaft and a driving output shaft.
双输入轴微机械陀螺仪可最大限度地发挥微结构的固有功能并实现最低成本。
Micromachined dual input axis gyroscopes have made the best use of inherent functions of the microstructures and therefore can reach the lowest cost.
一变速箱侧电机，其同时与变速箱的输入轴和电控离合器的从动轴元件相联。
And it contains a gear-box side-generator, which connects with the inlet shaft of the gear box and the driven shaft element of the electrically-controlled clutch simultaneously.
输入轴碳封圈密封面产生浮泡；碳封圈报废。输入轴上的密封面划伤，研磨修复。
Input seal: input carbon seal was blistered on the sealing face; the input carbon seal was scrap. Sealing face on the input shaft was scratched, and was lapped.
输入轴与齿圈（蓝色）连接，输出轴与行星架（绿色）相连，行星架上装有多片离合器。
The input shaft is connected to the ring gear (blue); The output shaft is connected to the planet carrier (Green) which is also connected to a "multi-disk" clutch pack.
变速箱侧输出轴通过万向联轴节与传动箱输入轴相连接，灭茬轴则由传动箱输出轴带动。
The side output shaft of the gear box connects with the input shaft of the wheel box through a universal coupling, the stubble cleaner shaft is driven by wheel box output shaft.
例如，将变速器装配到离合器壳上时，必须使变速器输入轴的中心线与发动机曲轴的中心线对准。
For example, using the gearbox fitted to the shell, the need for gearbox input shaft axis lines at the engine crank axis lines.
输入轴键受到固定螺钉的保护，输入和输出轴键配置实现最佳的刚性连接以提供更好的扭矩传送。
With the input shaft key secured with a set screw, an input and output shaft key configuration delivers optimum positive connection for superior torque transmission.
基准选择以变速箱箱体的输入轴和输出轴的支承孔作为粗基准，以顶面与两个工艺孔作为精基准。
The reference is chosen tobe the base of the input shaft and the output shaft of the gearbox, and the top and the two technological holes are used as the reference.
驱动电机的输出轴通过相互串接的第一普通联轴器和第一柔性联轴器同扭矩传感器的输入轴连接。
The output axle of the driving motor is connected with the input axle of the torque sensor through a first normal coupling and a first flexible coupling connected in series.
由于模型中存在参数的不确定性，利用定量反馈理论原理，设计了变速器输入轴速度鲁棒控制系统。
Owing to the existence of uncertainty in the model, a robust control system of transmission input speed is designed using quantitative feedback theory.
本实用新型涉及一种轴与轴之间的连接结构，特别涉及一种电机出轴与减速齿轮箱输入轴连接结构。
The utility model relates to a link construction between shafts, particularly relates to a link construction between the output shaft of an electric motor and the input shaft of a reduction gear box.
2减速机输入轴处轴肩处未细致考虑过渡圆角的曲率半径和变化曲线使应力集中严重发生疲劳破坏。
2 the curvature radius and the change curve of the transition fillet at the shoulder of the input shaft of the reducer are not carefully considered.
2减速机输入轴处轴肩处未细致考虑过渡圆角的曲率半径和变化曲线使应力集中严重发生疲劳破坏。
2 the curvature radius and the change curve of the transition fillet at the shoulder of the input shaft of the reducer are not carefully considered.
应用推荐