• 为了了解基因与环境的关系,研究人员采用了久经考验的双胞胎模型。

    To tease out the effects of genes and environment, the researchers turned to the time-tested model of twins.

    youdao

  • 两年以上农业、卡车轮胎模具设计经验。

    More than two years of agriculture truck tire mold design experience.

    youdao

  • 但该模型把整个汽车看作一个刚体,使用线性轮胎模型。

    But it regards the whole automobile as a rigid body, USES the linear tire model.

    youdao

  • 在不变载荷下以时变侧偏角为激励,对轮胎模型进行了计算。

    It is analyzed under time-varying side slip angle and constant wheel load.

    youdao

  • 介绍了小型轴承套的胎模锻造工艺,并详述了组合套模的设计要点。

    The die forging process for the small type bearing bushings has been described in this article, as well as the design outline of the assembled sleeve die.

    youdao

  • 产品被广泛用于水轮机、注塑机、汽车轮胎模具等。

    Used in water turbines, injection molding machinery, packing machines, construction equipment, tire moulds etc.

    youdao

  • 从轮胎模型和运动分析、整车运动和受力分析两方面介绍了客车动力学模型。

    From two aspects of the tire model and kinematical analysis, vehicle kinematics and force analysis, the bus dynamics model is introduced.

    youdao

  • 汽车轮胎模具网络化制造的实施将有效地提高轮胎模具产品的开发效率和质量。

    The efficiency and quality of tire mould design are effectively increased with the application of the networked manufacturing technology.

    youdao

  • 结合工厂实际分析了齿轮胎模失效方式及其产生原因,提出了提高胎模寿命的途径。

    Based on reality of the factory, analyze failure forms and causes of loose tooling of the gear, and present how to improve service life of loose tooling.

    youdao

  • 采用商用有限元软件DEFORM3D对半轴套管胎模锻成形过程进行了计算机模拟。

    The loose tooling forging of half shaft bushing on the steam-air forging hammer is numerically simulated using FEM software DEFORM3D.

    youdao

  • 并以轮胎模具的花纹造型为例,阐述了平面曲线向自由曲面映射在工程中的实际应用。

    The method of the least distortion mapping of planar curve to free surface is also discussed.

    youdao

  • 在轮胎静垂直特性建模的基础上,探讨了利用轮胎模态参数对轮胎纯侧偏特性的建模。

    Based on the model of tire static vertical properties, the modeling of tire pure cornering properties by using modal parameters is studied.

    youdao

  • 本文用一轮胎模型对这一现象进行了理论分析,并得到了与实验数据基本一致的结果。

    A tyre model is proposed in this paper to deal with the problem. The analysis result shows a satisfactory agreement with the experiment data.

    youdao

  • 样件以胎模定位,胎模表面根据本体CAD数据加工,表面倒PU胶,保证不划伤本体表面。

    Product parts located by fixture surface, which milled according to parts surface CAD data, and then coated by PU, to prevent the parts surface from being scratched.

    youdao

  • 分析了轮胎模态分析的试验方法及其在轮胎设计中的应用,并建立了轮胎模态分析试验系统。

    The tire modal test and its application to the tire structure design were analysed, and a tire modal analysing test system was established.

    youdao

  • 本文以某轻型客车为研究对象,对该车制动过程进行分析,建立了整车模型、单轮模型、轮胎模型和制动器模型等。

    This thesis studied certain light-duty bus, which analyzed braking process of this bus and built whole vehicle model, single wheel model, tire model and arrester model.

    youdao

  • 文章阐述了将并行工程思想引入轮胎模具设计与制造过程的意义,论述了基于并行工程过程管理技术的轮胎模具设计开发过程。

    The importance of applying the thoughts of parallel engineering to design and manufacturing of tyre molds is discussed, and the mold design and development process described.

    youdao

  • 针对ABS仿真计算的需要,对整个防抱系统进行了建模,包括轮胎模型、车辆模型、制动器模型、液压系统模型和控制器模型;

    The whole ABS models are established for the simulation requirement, including tire-road model, vehicle dynamic model, brake disk model, hydraulic system model and the controller model.

    youdao

  • 本文首先建立用于电子稳定程序的汽车模型,包括车身模型、悬架模型、转向模型、轮胎模型、制动系统模型、发动机模型和传动系模型。

    In this paper we firstly build a vehicle dynamic model, including vehicle body, suspension system, steering system, tire model, braking system, engine model and transmission model.

    youdao

  • 本文首先建立用于电子稳定程序的汽车模型,包括车身模型、悬架模型、转向模型、轮胎模型、制动系统模型、发动机模型和传动系模型。

    In this paper we firstly build a vehicle dynamic model, including vehicle body, suspension system, steering system, tire model, braking system, engine model and transmission model.

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定