也讨论了真空退火的影响。
对氢脆的危害进行了探讨，得出了适宜的真空退火条件。
The harmness of the hydrogen frangibility is discussed, and then the appropriate conditions of vacuum anneal are gained.
该设备也适用于多种激光晶体的生长和激光晶体的真空退火。
The puller also applied growing and vacuum anneal of laser crystal.
对制备的薄膜进行了真空退火处理，并对退火前后的薄膜进行了拉曼结构分析。
The prepared films were treated by vacuum annealing, and the structure of films before and after annealing was studied by Raman Spectrum.
采用各种分析手段研究了沉积温度和真空退火处理对薄膜结构、表面形貌及光电性能的影响。
The effects of substrate temperature and post deposition vacuum annealing on structural, electrical and optical properties of ZMO: ga thin films were investigated.
从光致发光光谱中发现，真空退火后的样品的紫外光谱峰显著增强，而深能级发射峰几乎消失。
From the pl spectrum, the UV emission peak of the sample annealed in vacuum increase clearly and deep-level emi.
用热舟蒸发方法在不同的沉积速率下制备了LaF3单层膜，并对部分单层膜进行了真空退火。
LaF3 single-layer coatings were prepared by thermal boat evaporation at different deposition rates. Some of these films were annealed in vacuum.
而在真空退火的生产过程中，退火工件温度的精确控制是一个典型的非线性、大时滞、强耦合的复杂控制问题。
The accurate control of the work pieces temperature in vacuum annealing furnace is a typical nonlinear large time delay and cross coupling complicated problem.
GH 5 18 8合金板材在真空退火中发生的粘接现象，说明必须重视金属元素在真空热处理中的蒸发问题。
From the adhesion phenomena of GH5188 alloy plates annealed in vacuum furnace, it is necessary to pay more attention to the evaporation of metal elements during vacuum heating.
分析了晶体真空退火前后的吸收光谱和着色等变化，并根据吸收系数变化计算了晶体分凝系数、浓度和吸收截面等参数。
The changes of crystal absorption spectrum and coloring were analyzed, and the correlative parameters such as separation coefficient, concentration and absorption cross section were calculated.
对多孔硅进行真空退火处理和暴露大气快速退火处理，将有机染料香豆素102（C102）镶嵌其中，研究镶嵌复合膜发光特性的变化。
In this article, porous silicon was annealed diversely in vacuum and in atmosphere, then, C102 dyes were embedded into both PS samples.
另外，对碳化硅薄膜的退火处理大多是在真空、空气、氩气或氮气气氛下进行。
In addition, the annealing process of SiC films is mostly carried out in vacuum, argon gas or nitrogen gas ambience.
高强度合金焊丝的生产包括酸洗、拉拔、退火、清洗、真空包装等工序，拉拔可采用“四拉四退”的生产工艺。
The production of high strength alloy welding wire includes pickling, wire drawing, anneal, cleaning, vacuum package and etc.
高强度合金焊丝的生产包括酸洗、拉拔、退火、清洗、真空包装等工序，拉拔可采用“四拉四退”的生产工艺。
The production of high strength alloy welding wire includes pickling, wire drawing, anneal, cleaning, vacuum package and etc.
应用推荐