林肯泵主要作用是密封注油头。
The main function of Linclion pump is to seal off the lubricator.
光敏印章机无需印台，可反复注油；
Photosensitive seal machine without stamp-pad stamp-pad may repeatedly note oil;
它是注油工艺机械不可缺少的注油设备。
不得使用其他物品托住正在注油的喷嘴。
它里面装着注油枪、垃圾袋和一个刮刀。
加油时不得离开注油泵。
具有对电力设备真空抽气和真空注油功能。
It possesses vacuum air bleeding and vacuum oil adding function.
请将手提式容器取出车辆，放置地面然后注油。
Before filling a Portable Container Remove Container From Vehicle And Place on Ground.
介绍了一种便排移动式高压大流量润滑脂注油机。
The paper introduces a portable HP heavy flow grease ejector and analyzes its work principle, structural features.
注油和泄放单元；
出于安全考虑在注油口和过滤器处设有弹性扣环。
导向架和箍圈、扭转铜套，以上各点每班注油一次。
Guide frame, tension sleeve and twisting copper sheathing are lubricated once per shift.
同时还介绍了变压器和互感器的真空注油干燥工艺。
At the same time, it also intro-duced dry technology for pouring oil into a transformer, a mutual inductor and so on in vacuum.
采用该系统后，注油速度和产品合格率得到显著提高。
After the system implementation, oil filling speed and product conformity is remarkably increased.
如果你不定期给发动机注油，它不定那天就会突然卡住。
If you fail to oil the engine regularly, it would seize up without warning.
注油孔为设在电机轴侧面的凹槽形或平面形注油孔。
The oil injection hole is a concave channel shape or planar oil injection hole which is arranged on the side surface of the motor shaft.
未来将有更多的太空行走，宇航员不得不分享注油枪了。
There will be more spacewalks, the astronauts are just going to have to share grease guns.
如果没有手动注油泵的话，在冷天气下发动机很难开车。
It can be difficult to start in cold weather if you don't have an engine primer.
汽油机注油时禁止烟火，否则会引起燃烧，危急生命安全。
No fire when filling gasoline to avoid burning or endangering life.
介绍基于工控机和PLC的汽车空调压缩机自动注油系统。
This paper introduces an auto air-condition compressor oil-filling system, which is based on Industrial PC and PLC.
某些开式齿轮装置，例如注油小齿轮或特别设计的循环系统等。
Some type gear device, such as oil or special design of small gear circulatory system, etc.
气体继电器安装方式和全密封变压器注油工艺是主要影响因素。
The way of installing QJ-40 gas-pressure relay and the oil injection craftwork of transformer are key influencing factors.
保证摆线减速器上的注油和排油塞还有转鼓环在同一平面上。
Ensure that the filling and drain plugs on the cyclo and bowl ring are in the same plane.
介绍变压器产生假油位的原因和危害，提出现场正确注油的方法。
Introduced the reason and harm of the false oil position in transformer and provided site correct oil injection method.
分析了由注油改为注水后，裂解气压缩机后冷器和段间罐的情况。
After using oil injection instead of water, analysis is also given to the actual situations of after-cooler of charge gas compressor and inter-stage tank.
介绍了裂解气压缩机注水系统，对压缩机注油与注水进行了比较。
Water injection system for charge gas compressor is introduced in the article and comparison is made for charge gas compressor with water injection and oil injection.
轻便且一处内免注油，有效延长电机寿命，减小维修时间和维修成本。
Light and oil-free within one year, effective to extend the motor life, reduced maintenance time and maintenance costs.
或为设在电机壳体侧壁或端面上对应于轴承部位的圆形或方形注油孔。
Alternatively, the oil injection hole is the round or square oil injection hole which is arranged at the positions of the side wall or end surface of the motor shell corresponding to the bearing.
假设放气塞和管接头的方位不正确，那么在变压器注油以后会构成气泡腔。
Range hypothesis vent plug and tube joint is not correct, then in the transformer oil injection will constitute a bubble chamber.
假设放气塞和管接头的方位不正确，那么在变压器注油以后会构成气泡腔。
Range hypothesis vent plug and tube joint is not correct, then in the transformer oil injection will constitute a bubble chamber.
应用推荐