光敏印章机无需印台，可反复注油；
Photosensitive seal machine without stamp-pad stamp-pad may repeatedly note oil;
它里面装着注油枪、垃圾袋和一个刮刀。
具有对电力设备真空抽气和真空注油功能。
It possesses vacuum air bleeding and vacuum oil adding function.
请将手提式容器取出车辆，放置地面然后注油。
Before filling a Portable Container Remove Container From Vehicle And Place on Ground.
介绍了一种便排移动式高压大流量润滑脂注油机。
The paper introduces a portable HP heavy flow grease ejector and analyzes its work principle, structural features.
注油和泄放单元；
导向架和箍圈、扭转铜套，以上各点每班注油一次。
Guide frame, tension sleeve and twisting copper sheathing are lubricated once per shift.
同时还介绍了变压器和互感器的真空注油干燥工艺。
At the same time, it also intro-duced dry technology for pouring oil into a transformer, a mutual inductor and so on in vacuum.
采用该系统后，注油速度和产品合格率得到显著提高。
After the system implementation, oil filling speed and product conformity is remarkably increased.
注油孔为设在电机轴侧面的凹槽形或平面形注油孔。
The oil injection hole is a concave channel shape or planar oil injection hole which is arranged on the side surface of the motor shaft.
未来将有更多的太空行走，宇航员不得不分享注油枪了。
There will be more spacewalks, the astronauts are just going to have to share grease guns.
如果没有手动注油泵的话，在冷天气下发动机很难开车。
It can be difficult to start in cold weather if you don't have an engine primer.
汽油机注油时禁止烟火，否则会引起燃烧，危急生命安全。
No fire when filling gasoline to avoid burning or endangering life.
介绍基于工控机和PLC的汽车空调压缩机自动注油系统。
This paper introduces an auto air-condition compressor oil-filling system, which is based on Industrial PC and PLC.
某些开式齿轮装置，例如注油小齿轮或特别设计的循环系统等。
Some type gear device, such as oil or special design of small gear circulatory system, etc.
气体继电器安装方式和全密封变压器注油工艺是主要影响因素。
The way of installing QJ-40 gas-pressure relay and the oil injection craftwork of transformer are key influencing factors.
保证摆线减速器上的注油和排油塞还有转鼓环在同一平面上。
Ensure that the filling and drain plugs on the cyclo and bowl ring are in the same plane.
介绍变压器产生假油位的原因和危害，提出现场正确注油的方法。
Introduced the reason and harm of the false oil position in transformer and provided site correct oil injection method.
分析了由注油改为注水后，裂解气压缩机后冷器和段间罐的情况。
After using oil injection instead of water, analysis is also given to the actual situations of after-cooler of charge gas compressor and inter-stage tank.
介绍了裂解气压缩机注水系统，对压缩机注油与注水进行了比较。
Water injection system for charge gas compressor is introduced in the article and comparison is made for charge gas compressor with water injection and oil injection.
轻便且一处内免注油，有效延长电机寿命，减小维修时间和维修成本。
Light and oil-free within one year, effective to extend the motor life, reduced maintenance time and maintenance costs.
或为设在电机壳体侧壁或端面上对应于轴承部位的圆形或方形注油孔。
Alternatively, the oil injection hole is the round or square oil injection hole which is arranged at the positions of the side wall or end surface of the motor shell corresponding to the bearing.
假设放气塞和管接头的方位不正确，那么在变压器注油以后会构成气泡腔。
Range hypothesis vent plug and tube joint is not correct, then in the transformer oil injection will constitute a bubble chamber.
经样机实验证明，跟踪可靠，注油准确，便于安装实施，是在线注油的好设备。
The on-line experiment shows that this oiling device possess high tracking and position accuracy and is easy to assemble.
出灰机内注油系统设计：总体原理、分配环设计与关键、空心滚轮轴强度校核等；
The lubrication system design inside Spiral Conical Dispenser including: the total theory, the key and the design for Dispensing Ring, the strength checkout of the hollow axle and etc;
流体动态注油轴承可保持稳定注油和减少内部震动，从而获得最小级别的噪音水平。
The Fluid Dynamic bearing keeps oil inside the bearing and thus reduce friction inbetween and keep the noise level to a minimum.
永磁除铁器的主要注油处：转动轴承，轧辊轴承，所有齿轮，活动轴承、滑动平面；
The permanent magnetic separator of the main oil: rolling bearing, roller bearing, all gear, a movable bearing, sliding plane;
填料采用柔性性石墨材料，密封性可靠。用户有要求时可提供填料隔环和注油脂结构。
Packing uses flexible graphite for dependable sealing performance. If request by users , packing spacer ring and greasing mechanism can be available .
分馏系统加注油浆防垢剂及控制合适的外甩油浆量和分馏塔底温度，可以有效防止结焦。
Coking in the fractionation system has been resolved by injecting slurry antifoulant and controlling the amount of slurry running down and the bottom temperature.
分馏系统加注油浆防垢剂及控制合适的外甩油浆量和分馏塔底温度，可以有效防止结焦。
Coking in the fractionation system has been resolved by injecting slurry antifoulant and controlling the amount of slurry running down and the bottom temperature.
应用推荐