这动物蜷成一团。全身尖尖的毛刺竖起来保护自己。
The animal protects itself by rolling up into a ball, with sharp hairs pointing outwards.
该文全面介绍了高压水射流去毛刺技术的原理、特点、技术要点以及应用情况。
The principles, features, key technical points and applications of this technique are described in this paper.
去毛刺线是否有启动前点检表？
着重阐述了去毛刺技术及其应用。
The technology of deglitching and its implementation are elaborated in particular.
毛刺是金属切削加工中产生的常见现象。
The burr is one of the common phenomena occurring in metal cutting.
卷边毛刺不应很容易形成，也不应太大。
在这种情况下，睫毛刺激眼睛产生眼泪。
In these conditions, the lashes irritate the eye, causing the tears.
最大毛刺0.2，不允许有明显的毛刺。
除去焊接飞溅并处理焊缝、毛刺使其光顺。
果皮有黄色和桃红色，覆盖有柔软的毛刺。
Its skin varies from yellow to dark pinkish red and is covered in soft spines.
羊毛刺激我的皮肤。
也检查所连接的管道是否清洁，没有碎片和毛刺。
Also check that the adjoining pipework is clean and free from debris and burrs.
刃口不能有毛刺。
简要介绍了高频直缝焊管内毛刺的形成和清除方法。
Briefed in the article are the inner burr formation of and the burring method for the hi-frequency straight welded tube.
通过分析，绝缘电阻不稳定的主要原因是机械加工毛刺。
Analysis shows that the main factor of instability of insulation resistance is machining burr.
毛刺：过多余量从锥模和顶模中挤出后引起的软滚子缺陷。
FLASH : Green roller defect, caused by excessive stock forced out between taper die and head die.
病灶边缘以分叶征、星芒状毛刺、界面锯齿征为主要特征；
Lobulation, long and stiff spiculation and sawtooth interface were imaging characteristic in their margin.
结论：毛刺征对SPLC的诊断和鉴别诊断具有较高价值。
Conclusion: Spiculation has the higher value in diagnosing and differentiating SPLC.
并阐述了去毛刺机在生产线上的应用情况以及它所带来的效益。
And expounds the application status of the deburring machine in production line and the benefits resulted from it.
简述了如何运用特殊设计的刀具去除零件表面毛刺的工艺方法。
This paper summarizes the processing method of using the special cutting tool for deburring.
时钟选择影响干扰，因为它仅仅改变电压毛刺到达的相对时间。
Clock timing affects crosstalk because it slightly changes the relative time of arrival of aggressive voltage spikes.
杆料不应有明显弯曲，裂缝、毛刺、起皮及影响使用的其他缺陷。
Rod should not have obvious camber, crack, burr, peeling or other defect affecting he further USES.
注射器表面必须清洁无杂质，不得有毛边、毛刺、塑流、缺损等缺陷。
The surface of the syringe must be clear and pure; rough edge, burr, plastic stream, defect are not allowed.
介绍了精密孔内和双联齿轮或带有拨叉槽齿轮槽中去毛刺的两种方法。
The paper introduced two methods of fin cutting in precision hole and dual gear (or gear with shifter fork) slot.
结果周围型肺癌主要表现为肿块分叶、边缘毛刺、胸膜凹陷及空泡征；
Results Peripheral lung carcinoma mainly showed a mass with lobulated shape, spicules of margin, pleural indentation and vacuole sign.
喷砂之后，应当除掉明显的毛刺、裂片、瑕疵和焊渣并对此处再次喷砂。
Burrs, slivers, scabs and weld spatter visible following blasting shall be removed and the area re-blasted.
切除蒙皮上的损伤区域并清除边缘毛刺，蒙皮切口最小半径0.5英寸。
Cut out the damaged area of skin and deburr the edges, the minimum radius of skin cutout is 0.5 inch.
特点：FPC加工专用钻头，切削锋利，能有效抑制毛刺和钻污的产生。
Features: With sharp cutting teeth for preventing burr and smear generation. Suitable for machining FPC and PTFE.
特点：FPC加工专用钻头，切削锋利，能有效抑制毛刺和钻污的产生。
Features: With sharp cutting teeth for preventing burr and smear generation. Suitable for machining FPC and PTFE.
应用推荐