同时还讨论了横向剪切效应。
本文介绍了一种新型横向剪切干涉仪的工作原理。
This paper presents the operating principle of a new lateral shearing interferometer.
考虑横向剪切作用的杆单元，对围岩稳定性有明显提升。
The bar element which considered the transverse shear effect has significantly improvement on tunnel stability.
本机采用直线式结构横向剪切、纵向剪切采用圆刀结构。
The machine adopts the linear model to cross cut and round-knife to slit.
在横向剪切干涉技术的基础上，讨论了几种波面重建的方法。
On the base of the lateral shear interferometry, different methods of shearing wave front reconstruction are described in this paper.
本文提出一种测试复合材料横向剪切弹性模量的参数识别方法。
This paper presents a method to identify transverse shear modulus for composite materials.
分析表明，横向剪切变形对钢筋混凝土厚板及集中荷载的影响很大。
The analyses show that the transverse shear deformation effect has a significant influence on the thick reinforced concrete slabs and the concentrated load condition.
分析了计及高阶横向剪切变形的正交各向异性弹性板自由振动的问题。
The transverse shear deformation effect is included by use of Mindlin-Reissner first-order shear deformation theory.
研究了扩散控制的界面滑动对纤维复合材料的横向剪切变形行为的影响。
The effect of diffusion controlled interfacial sliding on the transverse shear deformation of fibrous composites is studied.
数值算例表明，对于复合材料旋转壳，横向剪切变形使其临界载荷降低；
The examples show that the critical load of composite shells of revolution will decrease when considering the transverse shear deformation.
结果表明：在跨高比较小时，横向剪切效应对板的弯曲性能有显著影响；
The results indicated that transverse shear effect affects greatly on the bending properties of the plank while the ratio of span-height was small.
基于弹性理论建立了考虑横向剪切变形时复合材料脱层梁的基本方程序。
The basic equations, including the transverse shear, are built on the basis of elastic theory.
改善后的模型能较好地反映横向剪切效应对复合材料层板屈曲特性的影响。
Thus the effect of transversal shearing deformation on the buckling characteristics of composite laminated plates can be investigated more accurately by means of the modified model.
本文研究了两种类型的二维横向剪切干涉仪：正交剪切棱镜型和网格光栅型。
Two types of two dimensional lateral shearing interferometers have been studied: orthogonal shearing prism and crossed grating.
所取厚板条考虑横向剪切变形和转动惯量，并取它的各阶振型为条向连续函数。
The transverse shearing deformation and rotational inertia are taken into consideration in the chosen thick plate strips.
用该方法实测了造船工业用的单向竹蔑积成胶合板的弯曲刚度与横向剪切刚度。
Followly, the bending rigidity and transverse shearing rigidity of one-way bamboo-stripe laminates applied to shipbuilding has been measured practically with this method.
刚度分析用有限元法完成 ，其中采用了一种考虑横向剪切影响的三角形单元。
The stiffness analysis is performed by the finite element method, in which a triangular element considering the transverse shear effects is used.
当壳体的横向剪切刚度很大时，证明了本文提出的精化理论同经典理论的一致性。
If we let the transverse shear stiffness approach to infinity, the governing equation of refined theory can be reduced to the classical thin shell equation.
经典的梁板弯曲理论由于未考虑横向剪切变形的影响而只能适用于细长梁和薄板。
Classical bending theory of beam and plate can only be fit for thin and long beam and thin due to without considering deformed influence of cross shearing.
在该单元构造过程中，考虑了肋骨弯曲、扭转、面内剪切和横向剪切变形的影响；
The formulation of the element considers the coupling effects between in-plane bending and torsion as well as transverse shear effects for the stiffeners.
我们的剪切板准直度测量仪是用于检查和调整激光光束准直度的横向剪切干涉仪。
Our collimation Testers are lateral-shearing interferometers that can be used to examine and adjust the collimation of laser light.
对横向剪切干涉仪和哈特曼波前传感器的波前探测和复原进行了类比推导和仿真计算。
The detection and reconstruction of wavefront by Lateral Shear Interferometer (LSI) and Hartmann Wavefront Sensor (HWS) have been deduced analogically and simulated numerically.
这类板的横向剪切变形效应必须予以考虑，因而层板不同层的表面法线的转角是不同的。
The effect of transverse shear deformation is considered and Angle of rotation of surface normal for each layer is different.
理论分析和实验测试表明，该棱镜消光比优于10 -3，且可以实现大的横向剪切。
It can be approved by the theory and experiment that the extinction ratio of the parallel beam splitter is better than 10 ~ (-3), and the shear difference is improved too.
预测的强度能够反映出横向剪切效应的影响，其影响只与载荷大小有关，而与跨高比无关；
The calculated strength could show the affection caused by transverse shear effect and the affection had only relation to the loading value and no to the ratio of span-height.
该方法计入了板的横向剪切变形和挤压变形影响，其基本方程如同经典理论一样简单易解。
In this new method the influence of transverse and squeeze deformation was considered, the basic equations are complacated easily like classical theory.
在分析动载荷下的应力和变形时，除考虑横向剪切效应外，还须考虑微段的惯性力和阻尼力矩。
In the analysis of the stress and deformation under dynamic loading, the inertia force and damping moment should be considered in addition to the transverse shear effect.
讨论了横向剪切变形，曲板几何参数，铺层数，铺展方式和初始几何缺陷等各种参数变化的影响。
The effects played by transverse shear deformation, panel geometric parameters, total number of plies, fiber orientation, and initial geometric imperfections are studied.
在常规横向剪切干涉仪的基础上，利用波前周期延拓的假设，基于小波变换的方法实现了波前重构。
On the assumption of wavefront prolongation, a new optical phase retrieval algorithm by conventional lateral shear interferometer with wavelet transform is introduced.
在常规横向剪切干涉仪的基础上，利用波前周期延拓的假设，基于小波变换的方法实现了波前重构。
On the assumption of wavefront prolongation, a new optical phase retrieval algorithm by conventional lateral shear interferometer with wavelet transform is introduced.
应用推荐