我们的剪切板准直度测量仪是用于检查和调整激光光束准直度的横向剪切干涉仪。
Our collimation Testers are lateral-shearing interferometers that can be used to examine and adjust the collimation of laser light.
比较了考虑横向剪切变形的几种力学模型,提出了一种新的假定剪应力沿板厚呈抛物线分布的分层模型。
This paper compared several mechanical models with transverse shear deformation and put forward a kind of layer model assuming that shear stresses vary parabolically through the plate thickness.
同时还讨论了横向剪切效应。
本文介绍了一种新型横向剪切干涉仪的工作原理。
This paper presents the operating principle of a new lateral shearing interferometer.
在横向剪切干涉技术的基础上,讨论了几种波面重建的方法。
On the base of the lateral shear interferometry, different methods of shearing wave front reconstruction are described in this paper.
本文提出一种测试复合材料横向剪切弹性模量的参数识别方法。
This paper presents a method to identify transverse shear modulus for composite materials.
分析表明,横向剪切变形对钢筋混凝土厚板及集中荷载的影响很大。
The analyses show that the transverse shear deformation effect has a significant influence on the thick reinforced concrete slabs and the concentrated load condition.
分析了计及高阶横向剪切变形的正交各向异性弹性板自由振动的问题。
The transverse shear deformation effect is included by use of Mindlin-Reissner first-order shear deformation theory.
研究了扩散控制的界面滑动对纤维复合材料的横向剪切变形行为的影响。
The effect of diffusion controlled interfacial sliding on the transverse shear deformation of fibrous composites is studied.
数值算例表明,对于复合材料旋转壳,横向剪切变形使其临界载荷降低;
The examples show that the critical load of composite shells of revolution will decrease when considering the transverse shear deformation.
结果表明:在跨高比较小时,横向剪切效应对板的弯曲性能有显著影响;
The results indicated that transverse shear effect affects greatly on the bending properties of the plank while the ratio of span-height was small.
改善后的模型能较好地反映横向剪切效应对复合材料层板屈曲特性的影响。
Thus the effect of transversal shearing deformation on the buckling characteristics of composite laminated plates can be investigated more accurately by means of the modified model.
本文研究了两种类型的二维横向剪切干涉仪:正交剪切棱镜型和网格光栅型。
Two types of two dimensional lateral shearing interferometers have been studied: orthogonal shearing prism and crossed grating.
所取厚板条考虑横向剪切变形和转动惯量,并取它的各阶振型为条向连续函数。
The transverse shearing deformation and rotational inertia are taken into consideration in the chosen thick plate strips.
用该方法实测了造船工业用的单向竹蔑积成胶合板的弯曲刚度与横向剪切刚度。
Followly, the bending rigidity and transverse shearing rigidity of one-way bamboo-stripe laminates applied to shipbuilding has been measured practically with this method.
刚度分析用有限元法完成 ,其中采用了一种考虑横向剪切影响的三角形单元。
The stiffness analysis is performed by the finite element method, in which a triangular element considering the transverse shear effects is used.
当壳体的横向剪切刚度很大时,证明了本文提出的精化理论同经典理论的一致性。
If we let the transverse shear stiffness approach to infinity, the governing equation of refined theory can be reduced to the classical thin shell equation.
经典的梁板弯曲理论由于未考虑横向剪切变形的影响而只能适用于细长梁和薄板。
Classical bending theory of beam and plate can only be fit for thin and long beam and thin due to without considering deformed influence of cross shearing.
对横向剪切干涉仪和哈特曼波前传感器的波前探测和复原进行了类比推导和仿真计算。
The detection and reconstruction of wavefront by Lateral Shear Interferometer (LSI) and Hartmann Wavefront Sensor (HWS) have been deduced analogically and simulated numerically.
这类板的横向剪切变形效应必须予以考虑,因而层板不同层的表面法线的转角是不同的。
The effect of transverse shear deformation is considered and Angle of rotation of surface normal for each layer is different.
在分析动载荷下的应力和变形时,除考虑横向剪切效应外,还须考虑微段的惯性力和阻尼力矩。
In the analysis of the stress and deformation under dynamic loading, the inertia force and damping moment should be considered in addition to the transverse shear effect.
在常规横向剪切干涉仪的基础上,利用波前周期延拓的假设,基于小波变换的方法实现了波前重构。
On the assumption of wavefront prolongation, a new optical phase retrieval algorithm by conventional lateral shear interferometer with wavelet transform is introduced.
文中还对楔板引入的横向剪切误差和相移误差进行了分析,最后给出了实验所得的一组相移干涉图。
The lateral shear errors and phase shift errors induced by wedge plates are also discussed, and the experimental results of phase-shifting vectorial-shearing interference fringes are given.
最后,本文以实例分析讨论了横向剪切变形、开孔大小、线布载荷位置和几何参数对临界载荷的影响。
Finally, some examples are given to show the effect of shearing deformation, the hole size, the position of linear load and the geometrical parameter on the critical load.
该方程除了包含通常的薄膜内力项和内矩项外,还反映了横向剪切影响、转动惯性效应和横向挤压影响。
Besides the usual membrane stresses and stress couples the equation also contains additional terms reflecting the influences of transverse shear deformation, rotatory inertia and transverse extrusion.
采用多胞模型、形状记忆合金一维本构关系分析方法,同时考虑横向剪切的影响,建立了层合梁的数学模型。
This model is developed based on the one-dimensional SMA constitutive equation and multi-cell model, and considers the influence of transverse shear deformation of the hybrid composite beam.
结果表明:四边铰支的正交异性层合板,当其长厚比小于30时,横向剪切变形对其位移和应力的影响是不容忽略的。
The results showed that the effects of traverse shear on displacement and strees are not ignorable, as the length thick ratio of laminate is less than 30.
本文基于高阶剪切变形理论,考虑横向正应变和横向剪切应变的影响,对受热复合材料层合板壳的非线性热动态响应进行分析。
Based on a model of a cantilever beam system with clearance restriction, its nonlinear dynamic response to harmonic excitation are studied qualitatively in experiments.
利用新的接触模型,采用忽略横向剪切变形的三维空间曲梁单元对三维曲井内钻柱的接触非线性进行了有限元分析,给出了一套计算方法。
Based on the new contact model, finite element analysis scheme of drill rods in contact with curved boreholes is given using Bernoulli spatial curved beam elements.
利用新的接触模型,采用忽略横向剪切变形的三维空间曲梁单元对三维曲井内钻柱的接触非线性进行了有限元分析,给出了一套计算方法。
Based on the new contact model, finite element analysis scheme of drill rods in contact with curved boreholes is given using Bernoulli spatial curved beam elements.
应用推荐