我感觉有榫舌和凹槽的木材才是环保的。
I suppose the environmental way would be to use tongue-in-groove lumber.
你分组件买这个书橱，再把它们卡榫对准组合在一起。
每一只不起眼的抽屉也是美丽的；前后左右四个面用燕尾榫依次连接，前面和两侧分别使用差别明显的木料，以造成对比的效果：浅色橡木可以配紫檀木，桃花心木可以配白蜡木。
Each humble drawer, too, was beautiful, with sides and front in deliberately contrasting woods linked by dovetails: light oak into rosewood, mahogany into ash.
那木匠用卡钳估量暗榫。
拆卸时将榫槽分离平移即可。
When disassembling, only need separating and moving the tongue and grooves.
榫舌可呈S形以与凹槽形成互锁关系。
The tongue can be S-shaped to form an interlocking relationship with the groove.
木材。组装。多榫接头连接。弯曲试验。
木材机加工刀具。榫口加工刀具。尺寸。
Mechanical tooling for wood. Cutters for rabbet. Dimensions.
你也可以买现成的圆木榫。
You can also buy readymade dowels from mail-order suppliers.
存储模块插槽两端的白色固定卡榫扳开。
Push the white retaining clips on each side of the memory socket outward.
所有孔打完后，用凿刀将榫孔边修方正。
Once all the holes are bored, square the ends and the sides of the mortise with a chisel (Photo 15).
红木家具的制作是用入榫方法，不用钉子。
榫舌可设在每块厚板的与凹槽相对的侧面上。
The tongue can be on the opposing side of each plank from the groove.
固定构件为带有马牙榫、马牙榫槽的固定板。
The fixed unit is a fixed plate with a dovetailed tenon and a dovetailed tenon mortise.
因此夹具设计是榫槽加工中的一个重要环节。
Therefore the fixture design in trough processing is an important link.
另外我们还买了一架电动榫凿和一个最新式的电钻。
Besides, we bought a power mortise chisel and an electric drill of the latest model as well.
文中简要介绍了涡轮盘枞树形榫齿精拉刀的设计方法。
This thesis briefly introduces the design methods of the fir-tree tenon tooth accurate broach of turbine disk.
本文研究实木榫建模与数控开榫计算机辅助制造技术。
This paper studies Wood Tenoner Modeling and Computer-aided manufacturing about numerical control tenon process.
涡轮盘榫槽夹具可以保证加工精度高，提高加工效率。
The turbine disk trough fixture may guarantee the processing precision is high, enhances the processing efficiency.
安装时，在纵向，将一地板的平榫与另地板的平槽配合；
When in installation, in the longitudinal direction, the flat tenon of one floor is matched with the flat slot of the other floor;
一般有三种方法来解决这个问题，圆木榫、饼干榫和木楔。
There are three common solutions to this problem: dowels, joining plates and splines.
先在要对接的边上每隔6 ~8英寸画一个圆榫定位标记。
Start by laying out the dowel locations every 6 in. to 8 in. along the joint.
做好圆榫后，在要对接的两边和榫孔内都涂上薄薄一层胶水。
Once your dowels are cut to size, spread a thin layer of glue in all the dowel holes and along the edges of the mating boards.
大多数榫头除了在长边方向有榫肩，在两个短边方向也有榫肩。
Most tenons also have shoulder cuts on the top and bottom edges.
大房间的天花板高18英尺（约合5.5米），采用榫槽镶板。
The ceiling in the great room is 18 feet, with tongue-and-groove paneling.
凸榫基础是在挡土墙底板底面设置一个与底板成整体的榫状凸块。
Tenon foundation is tenon type integer block under the foundation slab of retaning wall, which is part of foundation slab.
凸榫基础是在挡土墙底板底面设置一个与底板成整体的榫状凸块。
Tenon foundation is tenon type integer block under the foundation slab of retaning wall, which is part of foundation slab.
应用推荐