对隐藏和显示引脚能力的控制。
选择隐藏行为引脚复选框。
这个引脚将会被隐藏。
该引脚是综合控制电路和电源地。
GND: This pin is the combined control circuitry and power ground.
当该引脚没有连接到任何东西。
每个引脚需要一个输出使能信号。
所有的引脚应该存在，甚至。
每个引脚是一个字符的特定部分负责。
这个“RSV”脚是浮空的输入引脚。
以下部分的代码是索引脚本的最后一部分。
The following section of code completes the indexing script.
在这整个城市，你可以听到一个引脚下降。
对于大阻值电阻﹐其引脚电阻是可忽略的。
For high resistance measurement, the lead resistance is negligible.
该引脚是误差放大器的输出，并提供环路补偿。
Compensation: This pin is the Error Amplifier output and is made available for loop compensation.
通常，这两个引脚应该就近连接后再接模拟地。
In general these two pins should be joined together and to the analog ground of the system.
图片1显示了摇杆武器与摇臂引脚和球轴承安装。
Photo 1 shows the rocker arms with the rocker arm pins and ball bearings installed.
数据切换的设备和输出通过写入和读取的引脚使用。
Data is toggled in and out of the devices through the use of the Write and Read pins.
一般来说是系统中断控制器上的所有输入引脚的个数。
Typically what is enumerated is the number of input pins on all of the interrupt controller in the system.
如果你不设置这个引脚音频将不会出现在模拟源别针。
If you do not set this pinout audio will not appear at the analog source pins.
要把电源和接地的引脚贯穿放置以便于电源和地对齐。
Position the power and ground feedthrough or abutment pins so that they align with corresponding pins in other cells.
一般来说，这个引脚接地，但它可连接到任何电压参考。
Generally, this pin is grounded, but it can be tied to any voltage reference.
如果您不能确定哪个板具有引脚驱动器，请打印头电缆。
If you are not sure which board has the pin drivers, follow the printhead cable.
为了计算增益和跨导，指的是部分意义上的固定电压引脚。
To calculate gain and transconductance, refer to the SENSE pin on fixed voltage parts.
其中数据总线sda是一个双向引脚，用于输入或输出数据。
Which the data bus SDA is a bidirectional pin used for input or output data.
在有些技术上，电源和接地引脚会伸出到边界或者边界外面。
In some technologies, power and ground pins extend to the edge or outside the boundary.
介绍了MAX038的特点、引脚功能、内部框图及工作原理。
The features, pin description, inner block diagram and application circuit of MAX038 are intro-duced.
引脚的边缘和阻挡层必须至少有半数的最小间距离开单元的边界。
The edges of pins and blockages must be at least one half the minimum spacing away from the cell boundary.
该引脚正好符合了扩锥孔的垂直轴的轴线，要么径向或切向轴表面。
The pin fits snugly in a reamed tapered hole that is perpendicular to the shaft axis and either radial or tangential to the shaft surface.
引脚围绕网格交叉点成矩形，在引脚图层通过最小金属宽度的一半指向所有四边。
The pin rectangle encloses the grid intersection point on all four sides by half the minimum metal width of that pin shape layer.
全局布线器不会把非格点引脚看成是阻挡层，这样导致你有一个过度乐观的设计结果。
The global router might not recognize off-grid pins as blocking the routing track and, as a result gives you optimistic results.
应用推荐