对隐藏和显示引脚能力的控制。
涂装电感，引脚牢固，高可靠性。
每个引脚需要一个输出使能信号。
这个“RSV”脚是浮空的输入引脚。
以下是所需引脚为标准接口。
以下部分的代码是索引脚本的最后一部分。
The following section of code completes the indexing script.
该引脚是误差放大器的输出，并提供环路补偿。
Compensation: This pin is the Error Amplifier output and is made available for loop compensation.
通常，这两个引脚应该就近连接后再接模拟地。
In general these two pins should be joined together and to the analog ground of the system.
图片1显示了摇杆武器与摇臂引脚和球轴承安装。
Photo 1 shows the rocker arms with the rocker arm pins and ball bearings installed.
出于这个原因，电路使用mclr引脚作为输出。
For that reason, this circuit USES the MCLR pin as an output.
数据切换的设备和输出通过写入和读取的引脚使用。
Data is toggled in and out of the devices through the use of the Write and Read pins.
一般来说是系统中断控制器上的所有输入引脚的个数。
Typically what is enumerated is the number of input pins on all of the interrupt controller in the system.
如果你不设置这个引脚音频将不会出现在模拟源别针。
If you do not set this pinout audio will not appear at the analog source pins.
要把电源和接地的引脚贯穿放置以便于电源和地对齐。
Position the power and ground feedthrough or abutment pins so that they align with corresponding pins in other cells.
最简捷的方法就是测量芯片的电源引脚与地之间的电阻。
The most simple and quickest way is to pin the power measurement chip with the resistor between.
这可能是执行一项特殊的测试单元与引脚点定位的压痕。
This can be performed on a special test unit with the pin-point positioning of an indenter.
为了计算增益和跨导，指的是部分意义上的固定电压引脚。
To calculate gain and transconductance, refer to the SENSE pin on fixed voltage parts.
其中数据总线sda是一个双向引脚，用于输入或输出数据。
Which the data bus SDA is a bidirectional pin used for input or output data.
在有些技术上，电源和接地引脚会伸出到边界或者边界外面。
In some technologies, power and ground pins extend to the edge or outside the boundary.
介绍了MAX038的特点、引脚功能、内部框图及工作原理。
The features, pin description, inner block diagram and application circuit of MAX038 are intro-duced.
引脚的边缘和阻挡层必须至少有半数的最小间距离开单元的边界。
The edges of pins and blockages must be at least one half the minimum spacing away from the cell boundary.
该引脚正好符合了扩锥孔的垂直轴的轴线，要么径向或切向轴表面。
The pin fits snugly in a reamed tapered hole that is perpendicular to the shaft axis and either radial or tangential to the shaft surface.
在VS引脚处需要额外的电容来处理负载电流的峰值和电位电机的再生。
Additional capacitance will be required at the VS pins to handle load current peaks and potential motor regeneration.
MJE3055T引脚说明：注意：本刊物提供的信息被认为是准确的。
MJE3055T Pinout: Notice: The information provided in this publication is believed to be accurate.
介绍宇通客车用松芝空调器控制面板接口每个引脚的功能接线及检测方法。
This thesis introduces the function, wire and checking method of the Songzhi air conditioner control panel used in Yutong coaches.
装配方式不合理，固定胶粘接强度不足和工艺不完善是导致引脚断裂的原因。
The fracture of the pins was caused by improper assembly flow and lower adhesion strength of the fixing glue.
引脚围绕网格交叉点成矩形，在引脚图层通过最小金属宽度的一半指向所有四边。
The pin rectangle encloses the grid intersection point on all four sides by half the minimum metal width of that pin shape layer.
全局布线器不会把非格点引脚看成是阻挡层，这样导致你有一个过度乐观的设计结果。
The global router might not recognize off-grid pins as blocking the routing track and, as a result gives you optimistic results.
每个引脚应该覆盖至少一个网格交叉点，由于软件连接最有效的是引脚在网格交叉点上。
Every pin should cover at least one grid intersection, because the software connects most efficiently to pins at grid intersections.
应用推荐