不锈钢复合钢制压力容器相对纯不锈钢压力容器便宜很多,又能起到相同的耐腐蚀作用,因此在石油化工行业中被广泛应用。
As pressure vessels made of stainless clad steel plates are much cheaper and have the same role of anti-corrosion, compared with those made of stainless steel plates, the former are used widely.
不锈复合钢的焊接是材料焊接工艺的难点之一。
The welding of stainless compound steel is one of the difficulties of material welding technique.
实践证明,只要遵循其焊接要点,不锈钢复合钢板的焊接质量是非常稳定的。
The practice proved that the welding quality of stainless steel clad plate was very steady if following the welding points.
介绍了内衬不锈钢复合钢管良好的使用性能,以及管与管之间和管与管件之间的几种连接方式。
It introduces the good usage properties of liner stainless steel compound steel pipe and several kinds of connection types between pipe and pipe and pipe with pipe fitting.
文中对缺陷产生的原因进行了分析,认为缺陷系不锈钢复合钢特殊的焊接结构和制造工艺所致。
In this article defect occurring reason was analyzed and hold that the defect was caused by the special welding structure of the stainless steel clad plate and fabrication process.
对不锈钢复合钢板的焊接特点进行了理论分析,总结出其焊接三要素:焊接坡口、焊接材料和参数、焊接顺序。
The paper analyzed the welding characteristic of stainless steel clad plate, and summarized three factors that were welding groove, welding materials and parameter, welding sequence.
管棚复合钢支撑技术,是一个通过超前管棚、支撑钢拱、白铁皮隔离、工作面封堵的相互配合和共同作用,形成了具有强大支护抗力的复合支护体系。
Pipe lodgepole-steel tunnel support technique is a strong composite support system consisting of advance pipe lodgepole, support stell vault, tin plate packer and working surface plug-back.
针对目前不锈钢复合板各生产方法存在的诸多不足,研制开发了钎焊轧制法。
Aiming at the fairly disadvantages in different realizations of stainless-clad steel plate at present, a new production method-brazing and soldering rolled method is developed.
采用镶铸工艺制备了硬质合金-45钢双金属复合耐磨材料。
The wear resisting composite of cemented carbide-steel 45 is fabricated by using casting-in process.
采用热化学反应法在Q235钢上制备纳米复合陶瓷涂层,对涂层进行结构分析及性能测试。
Nano-scale composite ceramic coating on Q235 was fabricated by thermochemical reaction method, and then structural analysis and performance test were conducted of the coating.
由于隐身性的需求,复合材料—钢混合结构的封闭式桅杆逐渐在舰船上使用。
To meet the needs of stealth, the enclosed masts with composite and steel materials are gradually applied on warships.
研究了铸造复合中锰奥氏体钢在冲击磨料磨损条件下的耐磨性能。
The wear resistance of casting composite medium manganese steel has been studied under the condition of impact abrasive wear.
介绍钢铝复合导电轨在三轨系统中的作用、工作原理、结构和常用材料。
The role, working principle, structure and commonly used material of steel aluminum composite conductor rail in the three-rail system are introduced.
为探讨多层钢胶复合材料的力学性能及联合工作特征进行了大量试验。
Experiments have been carried out to explore mechanical properties and co working characteristics of the multilayer steel glue composite material.
为考核纤维增强攻坚战斗部在混凝土中的爆炸毁伤效应,对裸装药、复合材料壳体、钢壳体装药在混凝土靶中的爆炸破坏效应进行了对比试验研究。
Experimental investigation on the blast effect of naked explosive, explosive charge covered with composite material shell as well as with steel shell in the concrete target is described.
介绍了板坯结晶器喂复合铝丝生产含铝钢的新工艺。
The new process of feeding compound aluminum wire to produce the aluminum steel in mould for slab was introduced.
通过铸造表面合金化和复合变质处理,使中锰奥氏体钢的强度、韧性和表面硬度显著提高。
The strength, toughness and surface hardness of medium Manganese austenitic steel have been increased greatly by casting surface alloying and complex modification.
酸可减少钢表面的酸可溶性物质,使得表面的高反应性的铬处于复合氧化物形式。
The acid depletes the steel surface of acid soluble species, leaving the highly reactive chromium on the surface in a compounded oxide form.
本文主要介绍了爆炸焊接不锈钢复合板中两种隐蔽性缺陷的形态、分布规律以及超声波检测。
This paper introduced the distribution and pattern of two conceal defects in explosive welding stainless clad steel plate and their ultrasonic inspection.
控制吹氩强度和吹氩时间,提高炉渣碱度和采用复合脱氧剂,使轴承钢的氧含量有所下降。
Controlling intensity and time of argon blowing, increasing slag basicity and adopting complex deoxidiser are helpful to reducing the oxygen content in bearing steels.
钢铝复合导电轨具有导电性好、耐磨损、重量轻、寿命长等优点。
The steel aluminum composite rail possesses such advantages as high conductivity, wear-resistance, low weight and long service life, etc.
提出一种钢筋与连续纤维复合而成的钢-连续纤维复合筋(SFCB)新型增强材料。
A new reinforcement material of steel fiber composite bar (SFCB) is presented in this paper.
本文对厚编织复合材料板由硬的钢圆柱弹丸穿孔问题进行了研究。
The study is concerned with perforation of thick woven composite plates by hard steel cylinder.
介绍了机械用铜-钢背复合材料的现状,制备工艺,材料特点,以及技术经济效果。
Present situation, production process, material features, technical effect and economical benefits of coppe-steel back composite for mechanical use were presented in the paper.
研究了液相烧结钢结硬质合金-铁双层复合材料的生产工艺。
The liquid phase sintering process of steel based carbide - iron bimetal composite was researched.
对结构钢多相复合组织及拉伸性能进行了研究。
The morphology of multiphase complex structure in low alloy structural steel and its tensile property were studied.
采用悬浮浇铸工艺并控制冷却速度成功地得到了钢颗粒增强纯铜基铸造复合材料。
Steel grain-reinforced pure copper cast composite was gotten successfully by suspension casting process and controlling the cooling rate.
采用粉末渗硼法,对三种WC含量不同的WC/钢复合材料进行渗硼处理。
WC/steel composites with different WC contents were boronized by powder boronizing.
结果表明,该钢经复合处理后,具有较好的表面硬度和良好的耐磨性,显著地增加了刀具的使用寿命。
The results showed that the steel after combined treatment had higher surface hardness and wear resistance, and prolonged the service life of cutting tool.
结果表明,该钢经复合处理后,具有较好的表面硬度和良好的耐磨性,显著地增加了刀具的使用寿命。
The results showed that the steel after combined treatment had higher surface hardness and wear resistance, and prolonged the service life of cutting tool.
应用推荐