如果孔不确切地是您想要它的地方，您能再采摘。
If the hole isn't exactly where you want it, you can pick again.
再千疮百孔的爱情，都不想用后悔来收场。
再采用粘结分离工艺，简单、巧妙地解决了叶片分离加工中叶片易变形、内孔精度易丧失的问题。
To solve the deformation and accuracy problem in the inner hole machining, we utilized stitching and partition process.
在上模节流棒槽内装入节流棒，将节流棒调节螺栓装配进节流棒的螺丝孔中，再装配上压块。
Mount restrictor bar into the restrictor bar groove of upper die, mount adjusting bolt for restrictor bar into the bolt hole in the restrictor bar, then mount lower press block, upper press block.
而水位异常图像出现的上升或下降形态，取决于井孔含水层系统在大震孕育过程的应力调整再积累阶段所处的构造部位。
However, decline or rise of water level anomaly depends on the tectonic position where the well aquifer lies in the process of stress regulation and re accumulation.
结论钢板边缘末位螺丝钉孔处再骨折的发生，主要与钢板两端应力集中有关。
Conclusion: the main reason of refracture through the last screw hole in plate fixation is over-stress concentration.
使用时将转环链放于两车之间，再通过插销将转环链两端（碰头座）的上下销孔连接在一起而后将插销锁紧即可。
When using the swivel chain between two cars, again through the bolt will turn on both ends of the chain (meet) the pin hole up and down together, and then the bolt locking.
方法：先采用AB-8型大孔吸附树脂法对高山红景天提取物进行分离，再通过HPLC法对高山红景天的主要成分红景天苷进行含量测定。
Methods:AB-8 Macroporous adsorptive resins were used to purify the extractive of Rhodiola, and then the content of Rhodioside was determined by using HPLC.
通过对石油焦燃烧过程中不同燃尽率焦样的比表面积和孔容积的测定，表明石油焦的比表面积和孔容积先增大，后减小到一定数值，最后再增大。
According to measurements, the specific pore surface area and pore volume of petroleum coke (PC) during combustion were found to: first increase, then decrease and increase again.
笔者认为，当种植体与种植孔大小适当、在种植孔中能保持稳定的位置时，羟基磷灰石涂层的钛种植体与孔之间没有必要再填充HAG。
There is no need to fill up the space between HA-coated titanium implant and suitable hole in the bone with HAG.
以波峰焊工艺焊点强度为标准，研究在不同钎料量下通孔再流焊焊点的强度。
This study benchmarked the strength of solder joints formed through the Through - Hole Reflow process against the traditional wave soldered joint.
这种旋转压力在实心坯中间出现了一个孔，再通过心轴成型成管。
This rotating pressure creates a hole in the middle of the billet, which is then formed into a pipe by a mandrel.
先把绳如图c所示穿过肩甲，再穿过胸甲的肩部孔，在腋下收紧打结。如图d所示。
First string through the shoulder plate as shown in Figure c, then string through chest plates shoulder plate hole, tighten the knot below the armpit as shown in Figure d.
采用新型的内孔电刷镀技术对失效的发动机缸套内表面进行了再制造。
Abstract :A novel bore brush electroplating technology was applied in remanufacturing for internal surface of failed engine cylinder body.
采用新型的内孔电刷镀技术对失效的发动机缸套内表面进行了再制造。
Abstract :A novel bore brush electroplating technology was applied in remanufacturing for internal surface of failed engine cylinder body.
应用推荐