• 这种旋转压力在实心坯中间出现了一个孔,再通过心轴成型成管。

    This rotating pressure creates a hole in the middle of the billet, which is then formed into a pipe by a mandrel.

    youdao

  • 结论钢板边缘末位螺丝钉孔处再骨折的发生,主要与钢板两端应力集中有关。

    Conclusion: the main reason of refracture through the last screw hole in plate fixation is over-stress concentration.

    youdao

  • 而水位异常图像出现的上升或下降形态,取决于井孔含水层系统在大震孕育过程的应力调整再积累阶段所处的构造部位。

    However, decline or rise of water level anomaly depends on the tectonic position where the well aquifer lies in the process of stress regulation and re accumulation.

    youdao

  • 以波峰焊工艺焊点强度为标准,研究在不同钎料量下通孔再流焊焊点的强度。

    This study benchmarked the strength of solder joints formed through the Through - Hole Reflow process against the traditional wave soldered joint.

    youdao

  • 笔者认为,当种植体与种植孔大小适当、在种植孔中能保持稳定的位置时,羟基磷灰石涂层的钛种植体与孔之间没有必要再填充HAG。

    There is no need to fill up the space between HA-coated titanium implant and suitable hole in the bone with HAG.

    youdao

  • 方法:先采用AB-8型大孔吸附树脂法对高山红景天提取物进行分离,再通过HPLC法对高山红景天的主要成分红景天苷进行含量测定。

    Methods:AB-8 Macroporous adsorptive resins were used to purify the extractive of Rhodiola, and then the content of Rhodioside was determined by using HPLC.

    youdao

  • 采用新型的内孔电刷镀技术对失效的发动机缸套内表面进行了再制造。

    Abstract :A novel bore brush electroplating technology was applied in remanufacturing for internal surface of failed engine cylinder body.

    youdao

  • 通过对石油焦燃烧过程中不同燃尽率焦样的比表面积和孔容积的测定,表明石油焦的比表面积和孔容积先增大,后减小到一定数值,最后再增大。

    According to measurements, the specific pore surface area and pore volume of petroleum coke (PC) during combustion were found to: first increase, then decrease and increase again.

    youdao

  • 通过对石油焦燃烧过程中不同燃尽率焦样的比表面积和孔容积的测定,表明石油焦的比表面积和孔容积先增大,后减小到一定数值,最后再增大。

    According to measurements, the specific pore surface area and pore volume of petroleum coke (PC) during combustion were found to: first increase, then decrease and increase again.

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定