结果表明:直接淬火工艺的淬火组织为板条马氏体和孪晶马氏体共存,且孪晶马氏体的含量较多。
The results show that the quenching microstructure of direct quenching technology consists of lath and twin martensites, and the amount of the latter is more.
淬火组织中马氏体与残余奥氏体的成分不均匀及磨削用量参数选择不当是导致裂纹出现的主要原因。
Uneven components of quenched martensite and residual austenite structure and improper grinding parameter are attributed to the main causes for cracks.
根据试样任意一点的温度和冷却速度对该点的组织进行预测,实现了T8钢淬火组织的计算机模拟。
According to the temperature and rate of cooling, microstructure forecast is carried out, computer simulation of quenching microstructure of T8 steel is accomplished.
研究了轧辊的预备热处理工艺对感应加热淬火组织的影响,感应加热温度和时间对组织和硬度的影响。
The effect of preheating treatment process of cold rolls on induction heat quenched structures and the effect of heating temperature and time on structure and hardness have been studied.
研究了淬火、回火工艺对低碳马氏体型高强度高韧性非调质钢的组织和性能的影响。
The effect of hardening and tempering process on the organization and performance of high-strength and high-toughness non-hardened-and tempered steel of low carbon martensite is researched.
采用真空控时急冷技术对H13钢热作模具进行淬火,可使之得到细小的马氏体组织,从而显著提高热作模具的冲击韧度。
Hot working dies of H13 steel vacuum quenched by the use of the time-controlled sudden cooling technology will obtain fine martensite.
结果表明:由于焊接电流过大,使焊缝产生淬火马氏体组织及较大的焊接残余应力,导致镀锌氢脆敏感性增加,造成吸油盘发生氢脆开裂。
The large welding current caused the formation of quenched martensite and the high residual stresses in the welding zone, resulting in the increase of zinc sensitivity of hydrogen attack.
文中着重模拟预测了它们的三维淬火瞬态温度场、相组织场及硬度场等。
This article puts emphasis on predicting the three-dimensional fields of transient quenching temperature, phase change and hardness of the try mentioned above.
研究了淬火温度和回火温度对ZG310- 510铸钢组织和力学性能的影响。
The Influence of quenching temperature and tempering temperature on mechanical properties and microstructure of ZG310-510 cast steel was studied.
分析讨论了二次淬火后马氏体的组织与亚结构,测量了该材料的主要力学性能。
The martensite substructure after quenching and the effect of grain size on the martensite substructure had been studied. The mechanical properties were measured.
不同的淬火温度使双相钢显微组织中不仅产生了不同体积分数的马氏体,而且也形成了不同数量的新生铁素体。
Different quenching temperatures lead to not only different amounts of martensite, but also different volume fractions of new ferrite.
结果表明,随着亚温淬火温度的升高,双相组织中马氏体的亚结构由孪晶型变成位错型,两相的变形能力和拉拔性能都得到改善。
Mecrostructure and mechanical properties of 20SiMnTi steel have been studied and analyzed when treated by different heat treatment process, by changing the sub-critical quenching temperatures.
局部淬火处理的齿轮具备比心部组织硬度高的表面硬度。
The case hardening process results in gears that have much harder surfaces than cores.
原始材料的组织状态为形变马氏体、淬火马氏体及残余奥氏体。
The original structure consists of deformation induced martensite, quenching martensite and retained austenite.
通过四种不同的分步淬火热处理工艺,相应地获得了四种不同组织的双相钢。
Four kinds of dual-phase steel with different morphology were developed by means of step quenching treatment routes.
研究了淬火、双级时效工艺参数对7475厚板组织、性能的影响。
The influences of the quenching and dual aging process on the structure and properties of 7475 alloy plates are studied.
研究了热处理工艺(包括均匀化处理、淬火方式和人工时效等)对6063铝合金组织和力学性能的影响。
The effect of heat treatment(including homogenizing treatment, quenching method and artificial aging)on the structure and mechanical property of 6063 aluminum alloy was studied.
研究了大型柴油机活塞项环槽激光淬火层的组织、耐磨性和磨损机理。
The structure, wear resistance and wear mechanism of laser quenched layer on the groove surface of the piston head were studied in this paper.
另外为消除二次淬火对ASTM 4130钢组织和性能的影响,应采用多层多道焊,并添加回火焊道。
In addition, to weaken the effect of double quenching on the microstructure and properties of ASTM4130 steel, multi-pass welding and temper bead should be adopted.
研究了淬火和回火温度对中碳低合金耐磨铸钢组织和力学性能的影响。
The influences of quenching and tempering temperature on microstructure and mechanical properties of medium-carbon-low-alloy wear-resistant cast steel were investigated.
对20钢进行不同强度交流磁场下的临界区淬火处理,观察相变后的组织。
To quench 20 steel in critical zone under different intensity alternation magnetic field and to observe the microstructure after phase transformation.
研究了由三种热处理工艺获得的全贝氏体等温淬火球铁的机械性能、组织状态及切削加工性能和耐磨性能。
The mechanical properties, structures, cutability and wear-resistance of full-bainite ductile iron obtained by using three kinds of isothermal quenching processes were investigated.
次层为淬火马氏体组织;
其经预先退火得到全部铁素体组织,然后等温淬火得到铁素体和贝氏体双相组织的基体。
The ferrite is obtained first through annealing, then biphase structure of ferrite and bainite is obtained through isothermal quenching.
研究发现,原材料的带状组织和淬火工艺的不合理是造成锯片基体淬火变形的两个主要原因。
Our study was found that two main reasons making the circular saw blades matrix distortion in quenching were banded structure and the unreasonable quenching process.
弹簧碾尖部位组织与弹簧其它部位组织不同,存在淬火屈氏体组织。
The structure of spring tine is not the same with that of any other parts and there is quenching.
摘要:对980钢进行激光相变硬化研究,分别对其空冷和水冷时淬火硬化层的宽度和深度进行测量,对其组织和硬化层硬度进行分析。
Abstract: The research of laser transformation hardening on steel 980 has been done in this paper. The width, depth and microhardness of quench zone was measured.
研究了淬火温度、淬火冷却方式和回火温度对高铬铸铁轧辊组织和性能的影响。
The influences of quenching temperature, cooling pattern and temper temperature on the structures and properties of high chromium cast iron roll were investigated.
研究了淬火温度、淬火冷却方式和回火温度对高铬铸铁轧辊组织和性能的影响。
The influences of quenching temperature, cooling pattern and temper temperature on the structures and properties of high chromium cast iron roll were investigated.
应用推荐