架子设计为厚壁的，聚乙烯类塑料材质的加筋立柱，和保持最大稳定性的地板。
Stands are constructed of durable thick-wall, polyethylene plastic with a structurally reinforced post and fillable base for maximum stability.
有些决定，如壁厚和销轴直径，可能取决于科学的计算，但非科学的部分的设计仍然是首要的。
Some decisions, such as wall thickness and pin diameter, may depend on scientific calculations, but the nonscientific component of design remains primary.
门级以下瘤胃内最多的是拟杆菌、厚壁菌门、螺旋体和纤维菌门。
Bacteroidertes, Firmicutes, Spirochaetes, and Fibrobacteres were the most abundant in rumen under phyla level.
最大的问题是如何找到合适的厚壁果酱罐子：如果买新的，也许还不如直接买便宜的果酱划算。
The hardest thing is getting hold of proper thick-walled jam jars; new, they can be more expensive than some cheap jams.
在燃料棒开始融化后一段时间里，热量可能融化四到八英寸厚的反应堆的容器钢壁。
研究者已证明动脉壁的增厚与中风危险的增加相关联，这种检测通常能够发现5%到20%的顾客有可探测的血小板增加。
Researchers have shown that a thickening of artery walls is associated with elevated stroke risk, and such scans typically find that anywhere from 5 to 20 percent of clients have detectable plaque.
它是高度密封，用钢铁和混凝土制成的非常厚的壁障。
The containment structure is a hermetically (air tight) sealed, very thick structure made of steel and concrete.
在厚壁休眠细胞如藻菌纲的厚孢子或接合子中明显的几层是常常能看见的。
Distinct layers are often visible in thick-walled resting cells such as chlamydospores or zygotes of phycomycetes.
不要去远低于45摄氏度，否则您将不会留下足够的壁厚。
Don't go much below 45 degrees or you will not leave enough wall thickness.
这些计算的最小必需的壁厚可能被使用作为认可的弯头标准。
The minimum wall required by these calculations may be used as the acceptance criteria for bends.
首先进行强度和稳定性计算，主要进行了筒体、端盖的壁厚计算、水压试验应力校核以及叶轮、轴的强度校核。
First of all, for strength and stability, mainly a cylinder, cover the wall, the water pressure check and impeller stress test, the axis of strength checking.
当整个厚壁圆筒达到屈服状态时，推导了在内压力和轴向力联合作用下的厚壁圆筒的塑性极限载荷表达式。
The relative formulations between limit loads (both axial force and internal pressure ) acting on it are derived while the whole thick-walled tube is led to the yielded state.
通过与已有文献的比较，得出的结论同时适用于内层管为薄壁管和厚壁管的情况。
The conclusions are applicable to the case where the inner tube is thin-walled or thick-walled in comparison with available literatures.
较大的直径使得强度指数性增加，但壁厚的增加只是线性地增加强度。
Making the diameter larger increases strength exponentially, while increasing the wall thickness only increases the strength linearly.
最后分别分析了材料性质、截面长宽比、管长和壁厚对最终变形模式的影响。
Moreover, the influences of material property, section properties, tube length and thickness to ultimate deformation modes are studied respectively.
表层是百叶窗、起保护作用的厚壁和微裂缝，这些都能突出建筑主题。
The blind facade, the protective thick wall, and the slight crevices, all these above reinforce the architectural theme.
尺寸，螺纹规，最小壁厚和爆裂压力，材料分类，各种质量要求和所规定的标记和标识要求等。
Dimensions, thread gaging, minimum wall thickness and burst pressure, material classification, various quality aspects and requirements for marking identification are stipulated.
提出的管坯壁厚精度概念极其控制方法具有普遍性，对于其它薄壁筒形件的制造工艺具有参考作用。
The introduction of the concept of bellows wall thickness accuracy has the universal significance and reference value for manufacturing technology of other thin wall tube like products.
螺纹尺寸规格说明，最小壁厚和爆裂压力，材料分类，以及规定的标记标识的要求等。
Thread dimensional specifications, minimum wall thickness and burst pressure, material classification, and requirements for marking identification were stipulated.
我认为两半的模具加上真空泵来提供压力能使结构更好，我也能更好的控制壁厚。
I believe molding two halves with a vacuum pump to provide pressure will produce a better structure and allow me to better control wall thickness.
该天盖壁是双层厚的。
塑料水槽的设计的内容包括制品的材料选择，壁厚的确定，收缩率的确定以及用UG软件绘制的过程。
The flume's design includes the selection of the material, thickness, contractibility and how to use UG to plot it.
探讨了影响注射成型厚壁塑料制品收缩变形的一些因素，提出了对实际生产有指导作用的建议。
Several factors affecting on contraction deformation of thick section injection moulding articles were investigated. Some practical proposals were given.
研究了在均匀径向压力作用下圆柱正交异性复合厚壁圆筒的弹-塑性应力场和位移场。
The elastic-plastic stress and displacement fields of cylindrically orthotropic composite thick-walled tube under uniform radial pressure are studied.
提出采用主磁通与漏磁通相结合的方法检测在用油管剩余壁厚的方法。
A measuring method combining main magnetic flux and magnetic flux leakage for approaching the residual wall thickness of the oil well tubing in-service was presented.
工厂检验芯偏移以及壁厚的频率？
What is the foundry's checking frequency for control of core shift and wall thickness?
计算结果表明，在最苛刻的加载方式下，轨姿控舱体的强度可以满足设计要求；壁厚尺寸是关键的优化设计变量。
The analysis result shows that the section can work reliably and the wall thickness is the key design variable.
计算结果表明，在最苛刻的加载方式下，轨姿控舱体的强度可以满足设计要求；壁厚尺寸是关键的优化设计变量。
The analysis result shows that the section can work reliably and the wall thickness is the key design variable.
应用推荐