The segregative phases and it's solution temperature in alloy IN783 were investigated.
研究IN783合金显微组织及析出相，测定偏析相的初熔点温度。
The effect of solid solution temperature on the structure properties of LY11 aluminium alloy is studied.
本文研究了固溶温度对硬铝LY11组织与性能的影响。
In addition, the hardness of the composite after aging decreases with the increase of solution temperature.
但随固溶温度的升高，时效后复合材料的硬度的提高幅度有下降趋势。
The result showed that 3 exhibited clear thermosensitivity, and its lower critical solution temperature was 28.
研究结果表明，3呈现较好的温敏性，低临界溶液温度为28。
The effects of solution concentration, solution temperature and film Renault number on absorption performance were studied.
分析了溶液温度、浓度、降膜雷诺数对吸收效率和传质系数的影响。
The effects of solid-solution temperature and holding time on the grain growth and hardness of GH4169 superalloy were investigated.
研究了热处理温度和保温时间对GH4169合金晶粒长大规律和硬度的影响。
The Lower Critical Solution Temperature(LCST)of the copolymers was determined by fluorescence probe and turbidity measurement method.
利用浊度法和荧光探针法测定了共聚物的最低临界溶液温度（LCST） 。
Polymers exhibited lower critical solution temperature (LCST), which showed almost concentration-independent behavior in the range of 2.
两种聚膦腈均具有较低临界溶液温度（LCST），在质量分数为2。
This dendrimer worked as a drug carrier with thermosensitive release capabilities, although it did not exhibit a lower critical solution temperature.
这树枝状担任药物载体的热敏释放的能力，尽管它不具有更低的临界溶解温度。
But can't think solution temperature rise is bad, if with other process conditions, with appropriate solution temperature rise will get a good effect.
但是不能认为升高溶液温度都是不利的，如果同其它工艺条件配合恰当，升高溶液温度也会取得良好效果。
The graft copolymer HPG-g-PNIPAM shows the Lower Critical Solution Temperature (LCST), and the relationship between the LCST and structure was studied.
测定了其聚合物的低临界共溶温度（LCST），并初步研究了聚合物的结构与LCST之间的关系。
The fiber showed circular section, homogeneous structure without sheath and core, splendid mechanical properties and wide water solution temperature range.
纤维呈圆形截面，无皮芯层，结构均匀，具有良好的力学性能和宽的水溶温度范围。
The relationship between solution temperature under standard heat treatment with the structure and properties of precision die forgings, was also presented.
叙述了标准热处理固溶加热温度与精化模锻件组织和性能的关系。
The secondary phase particle dissolves back more with the increase of solution temperature and holding time, but recrystallization will occur, grains grow up.
随固溶温度升高和固溶时间的延长，第二相颗粒回溶较多，但会发生再结晶，晶粒发生长大。
The factors that affect the performance, such as cathode catalyst loading, methanol concentration, and the methanol solution temperature, have been investigated.
同时对影响电池性能的因素，如阴极催化剂的用量，甲醇的浓度和甲醇的温度等进行了考察。
The solution temperature was displayed on the virtual panel during the brush plating process, and it would be alarmed as the temperature exceeded the permitted value.
在刷镀过程中，镀液温度实时显示在计算机的虚拟面板上，当镀液温度超出许用值时仪器报警。
For a given extrusion ratio, mechanical properties of alloy wire decrease and conductivity increases with increase of on-line solution temperature and ageing temperature.
当挤压比一定时，随着在线固溶温度与时效温度的升高，线材的力学性能下降，导电性能升高。
Methanol is suitable solvent for producing tetrabromobisphenol a, the factor of affecting product quality has: Solution temperature and acidity and fee ding speed of bromine.
甲醇是生产四溴双酚a合适的溶剂，对产品质量有影响的因素有：溶液温度、酸度和加溴速度。
A resolution is put forward to eliminate the influence caused by three factors, i. e. solution temperature, high inner impedance of glass electrode and deviation of electrode.
针对影响测量准确性的三个因素：溶液温度、玻璃电极高内阻和电极偏差，提出了解决办法。
The freezing points of ethanol solution, air temperature in the hall, air temperature near ice surface, ice temperature, solution temperature in the basin are given based on the measured data.
依据实测数据，给出酒精溶液冻结温度和制冰过程中冰池大厅气温、冰表面附近气温、冰温和溶液温度。
A grander solution, outlined in a forthcoming Bulletin of the American Meteorological Society, would be to provide a single online databank of all temperature data and analysis.
美国气象学会公报即将公布整个气温数据和分析的唯一在线数据库，这将是更好的解决方案。
So when I have a pure water solution, the total pressure is going to be the same as the vapor pressure of water at a particular temperature Let's take temperature fixed at some value.
当溶液是纯水时，总压强应该等于纯水，在特定温度下的蒸汽压，我们让温度固定。
Strong erosion: the metal workpieces dip in with high and certain temperature erosion of solution, to remove metal workpieces surface oxides and corrosion things process.
强浸蚀：将金属制件浸在较高浓度和一定温度的浸蚀溶液中，以除去金属制件表面上氧化物和锈蚀物的过程。
The temperature at which a solution of a surfactant or glycol starts to form micelles (molecular agglomerates), thus becoming cloudy.
表面活性剂溶液或乙二醇开始形成胶粒(分子聚集)的温度，溶液开始变得浑浊。
The Automatic Temperature Compensation (ATC) mechanism automatically adjust the readings for temperature variations of the solution.
自动温度补偿测量仪（ATC）自动调节溶液温度改变的读数。
Temperature, which applies to the solution or the liquid under test, should be maintained within 0.5 of the stated value.
供试溶液或者液体的温度应该保持在要求数值加减0.5的范围内。
This paper Points out possibility of electric shock due to low - temperature Hot Water Floor Radiant Heating Applied in Toilet, the reason is analysed and solution is also presented.
指出了卫生间采用低温热水地板辐射供暖系统，存在可能导致电击事故的隐患，分析了其产生的原因，给出了解决办法。
The increase of burning temperature causes the copper extraction into solution up to 98%, while copper extraction into solution from non-burned samples was up to 6%.
升高的温度导致溶液中铜的萃取物高达98%，而在没燃烧样品的铜的萃取物到达6%。
The increase of burning temperature causes the copper extraction into solution up to 98%, while copper extraction into solution from non-burned samples was up to 6%.
升高的温度导致溶液中铜的萃取物高达98%，而在没燃烧样品的铜的萃取物到达6%。
应用推荐