The effect of solid solution temperature on the structure properties of LY11 aluminium alloy is studied.
本文研究了固溶温度对硬铝LY11组织与性能的影响。
The effects of solid-solution temperature and holding time on the grain growth and hardness of GH4169 superalloy were investigated.
研究了热处理温度和保温时间对GH4169合金晶粒长大规律和硬度的影响。
The fiber showed circular section, homogeneous structure without sheath and core, splendid mechanical properties and wide water solution temperature range.
纤维呈圆形截面，无皮芯层，结构均匀，具有良好的力学性能和宽的水溶温度范围。
The secondary phase particle dissolves back more with the increase of solution temperature and holding time, but recrystallization will occur, grains grow up.
随固溶温度升高和固溶时间的延长，第二相颗粒回溶较多，但会发生再结晶，晶粒发生长大。
The solution temperature was displayed on the virtual panel during the brush plating process, and it would be alarmed as the temperature exceeded the permitted value.
在刷镀过程中，镀液温度实时显示在计算机的虚拟面板上，当镀液温度超出许用值时仪器报警。
But can't think solution temperature rise is bad, if with other process conditions, with appropriate solution temperature rise will get a good effect.
但是不能认为升高溶液温度都是不利的，如果同其它工艺条件配合恰当，升高溶液温度也会取得良好效果。
The factors that affect the performance, such as cathode catalyst loading, methanol concentration, and the methanol solution temperature, have been investigated.
同时对影响电池性能的因素，如阴极催化剂的用量，甲醇的浓度和甲醇的温度等进行了考察。
For a given extrusion ratio, mechanical properties of alloy wire decrease and conductivity increases with increase of on-line solution temperature and ageing temperature.
当挤压比一定时，随着在线固溶温度与时效温度的升高，线材的力学性能下降，导电性能升高。
A resolution is put forward to eliminate the influence caused by three factors, i. e. solution temperature, high inner impedance of glass electrode and deviation of electrode.
针对影响测量准确性的三个因素：溶液温度、玻璃电极高内阻和电极偏差，提出了解决办法。
The freezing points of ethanol solution, air temperature in the hall, air temperature near ice surface, ice temperature, solution temperature in the basin are given based on the measured data.
依据实测数据，给出酒精溶液冻结温度和制冰过程中冰池大厅气温、冰表面附近气温、冰温和溶液温度。
The Lower Critical Solution Temperature(LCST)of the copolymers was determined by fluorescence probe and turbidity measurement method.
利用浊度法和荧光探针法测定了共聚物的最低临界溶液温度（LCST） 。
The graft copolymer HPG-g-PNIPAM shows the Lower Critical Solution Temperature (LCST), and the relationship between the LCST and structure was studied.
测定了其聚合物的低临界共溶温度（LCST），并初步研究了聚合物的结构与LCST之间的关系。
Methanol is suitable solvent for producing tetrabromobisphenol a, the factor of affecting product quality has: Solution temperature and acidity and fee ding speed of bromine.
甲醇是生产四溴双酚a合适的溶剂，对产品质量有影响的因素有：溶液温度、酸度和加溴速度。
Methanol is suitable solvent for producing tetrabromobisphenol a, the factor of affecting product quality has: Solution temperature and acidity and fee ding speed of bromine.
甲醇是生产四溴双酚a合适的溶剂，对产品质量有影响的因素有：溶液温度、酸度和加溴速度。
应用推荐