This turning effort is carried by driving keys engaging slots on the flange.
这种转向力是通过驱动钥匙连接法兰上的槽来实现的。
The flange also ensures that there will always be some water left in the tank (about half an inch) to prevent the black plastic from melting.
法兰盘的高度应该有半英寸，以确保水箱总能存有一定的水，使黑色塑料膜不至于熔化。
CAUTION: Do not use any sharp tools such as a crowbar or screwdriver on the rubber during installation. Sharp instruments can damage the flange face and cause possible leakage.
警告：在安装期间，不要采用任何尖锐的工具，如：撬棍或螺丝刀等。尖锐的工具可能会损伤法兰面，从而可能导致泄露。
For ease of installation, insert all flange bolts through the valve flange and then through the sleeve flange, but do not let the bolts extend beyond the surface of the flange rubber (See Figure 4).
为了使安装容易些，可以将所有法兰螺栓穿过阀门法兰，然后穿过套管法兰，但是不要让螺栓超过法兰橡胶表面(参阅图4)。
The large flange welded by using EBW has been successfully used in the array antenna of new radar.
采用电子束焊完成的大型法兰已成功地应用于某新型雷达的阵列天线。
Its flange USES the bolt joint.
其法兰处采用螺栓联接。
Torque all flange bolts in a star pattern.
按照星形模式紧固所有法兰螺栓。
Using thread or flange capillary connection.
采用螺纹或法兰毛细管联接。
The said flange connected with the central axis is a polygon.
所述的与中心轴连接的法兰盘为多边形。
One integral flange on the outer ring and one loose flange ring.
外圈带一个整体式法兰和一个松配合法兰圈。
Refer to Table1 for flange classifications and serial parameters.
法兰分类及系列参数见表1的规定。
A flange which contains insulating material to separate the metal parts.
带有绝缘材料的法兰，用来分开金属部件。
Do not rely on the flange bolting to support the valve or connecting pipeline.
不能依赖法兰螺栓来支撑阀门或连接管道。
Replacement sleeves are made with one flange end slightly softer than the other.
用来更换的套管其一端的法兰比另一端稍微柔软一些。
The urethane liner extends over the flange face to serve as the valve's flange gasket.
这种氨基甲酸乙酯延展覆盖到法兰表面，起到阀门法兰衬垫的作用。
Lode parameters are used to analyze the stress and the strain of the flange in calendering.
应用罗代参数对压延工艺中的凸缘部分进行应力和应变分析。
However, ANSI flange design of the main shortcomings is that it can not guarantee no leakage.
然而，ANSI法兰的主要设计缺点是它不能保证无泄漏。
Cracks have been found in the flange and web splices at groove welds in at least four Bridges.
至少在四座桥梁的翼缘板和腹板拼接坡口焊缝中发现了裂纹。
The large anticorrosion flange can be divided into pushing, pressing, forging, casting and so on.
大型防腐法兰以制作方法划分可分为推制、压制、锻制、铸造等。
The bushing ring flange suitable temperature is decided by the designer according to the situation.
衬环法兰的适用温度由设计者根据情况决定。
When flange is withstanding axial tension or crook moment, its purpose should be considered otherwise.
当法兰承受轴向拉力或弯矩时，应另行考虑其作用。
I plant mainly produces all kinds of high, medium, low flange, ring, forging, gear and special flange.
我厂主要生产各种高、中、低压法兰，环件、锻件、齿轮及异型法兰。
Valves can also be furnished with flange bolt holes drilled for through bolting, except in the chest area.
阀门也可以配置法兰螺栓孔，用于贯穿式螺栓，但不能穿过阀腔区域。
Interface leak So, gaskets are different, the requirements of the flange surface roughness is not the same.
所以，垫片不同，所要求的法兰表面粗糙度也不相同。
The design of bearing flange structures has a significant effect on saving cost and lightweight of heavy load gearbox.
重载变速箱支承法兰盘的结构设计对节约成本、减小箱体整体重量有着重要的影响。
One end of it is a movable flange whose installation gap is adjustable, making dismantlement and maintenance convenient.
一端采用本公司特有的活动法兰，可调节安装间隙，方便拆装和维护。
The flange maximum allowable working pressure should not be smaller than the computed pressure of this flange in operation.
法兰最大允许工作压力应不小于该法兰在使用条件下的计算压力。
If there is leakage at the flange face-seal only, further tightening of bolts will almost never stop any flange joint leak.
如果泄露仅仅出现在法兰面密封上，进一步的螺栓紧固基本上并不会阻止法兰连接部分的泄漏。
Note: You may increase the torque on the rubber sleeve up to two times the specified value without causing sleeve or flange damage.
注意：在橡胶套管上增加的扭矩可以达到规定扭矩值的两倍，在此时仍然不会对套管或法兰造成损害。
Note: You may increase the torque on the rubber sleeve up to two times the specified value without causing sleeve or flange damage.
注意：在橡胶套管上增加的扭矩可以达到规定扭矩值的两倍，在此时仍然不会对套管或法兰造成损害。
应用推荐