Remove the bottom flange cover.
拆卸底部法兰盖。
The influence of the flange form.
法兰形式的影响。
Mating flange ID must match sleeve ID.
配套法兰内径必须与套管内径匹配。
We can roll, bend, or flange a plate.
可滚压，弯制和折边。
Body, bonnet, connection flange, disc.
阀体，阀盖，连接法兰，阀瓣。
Remove cover and clean flange and reseal.
拆卸车轴护罩，清洁凸缘并重新密封。
It is the replacement of insulating flange.
它是绝缘法兰的替代产品。
We are a special steel flange supplier in China.
我们是中国专业钢制法兰供应商。
It's ideal equipment for bend Angle iron flange.
是制作角铁法兰、型材滚圆弯曲的理想设备。
Press the flange and replace the side sealing ring.
压紧法兰(均匀用力)更换侧密封圈。
Allow the sleeve flange to return to its original position.
允许套管法兰回到它的初始位置。
Air will be absorbed from system entrance flange by draw air pipe.
气体由系统入口法兰通过吸气管路吸入。
Note: If match special flange, please let us know before production.
注：如果法兰接口特殊，请与我们联系。
Different flange form, requires the use of gaskets are also different.
不锈钢法兰形式不同，要求使用的垫片也不同。
Tighten enough to hold the wheel in place, without distorting the flange.
紧固的标准是：砂轮牢牢固定住，而轮缘又不会变形。
The relation between stress and strain of upper or lower flange is linear.
上下翼缘应力与应变关系均为直线。
The long neck flange should have stress-relief heat treatment after welding.
拼接法兰应进行焊后消除应力热处理。
Wind power base, large gear ring and pressure vessel flange production, etc.
风力发电基座、大型齿圈、压力容器法兰等的制造。
Cause of the surface wrinkling of flange made of 15-5ph cast steel was studied.
对铸钢15 - 5ph法兰盘表面抛丸后皱皮的产生原因进行了分析。
The analysis method has some reference value for flange structural optimization of the size.
该分析方法对法兰盘结构尺寸的优化具有一定的参考作用。
Please give indication of flange, material and operating pressure if you need other standard.
当需要其他标准法兰、材质或操作压力时请在订货时注明。
Please give clear indication of flange, material and operating pressure if you need other standard.
当需要其他标准法兰、材质或操作压力时请在订货时注明。
Please give clear indication of flange, material and operating pressure if you need other standard.
其他标准法兰、材质或操作压力时请在订货时注明。
Is suitable for through flange valve sealing pressure and valve body intensity pressure performance test.
适用于直通法兰式阀门的密封压力和阀体强度压力性能试验。
Flange member, noice silencer, tube end closure or connection device, and forming method and device.
法兰部件，消声器，管端闭锁或联结装置及其形成方法和装置。
Flange member, noice silencer, tube end closure or connection device, and forming method and device.
法兰部件，消声器，管端闭锁或联结装置及其形成方法和装置。
应用推荐