Cost also became a huge factor, as increased reliance on the datacenter and the increase in data capacity also required substantial increase in cooling costs.
随着企业对数据中心的依赖性和数据容量的增加，冷却成本显著增加了，这使成本成为一个重要的因素。
Decadal and longer changes in sunspot activity impacting warming and cooling cloud cover patterns are now being recognized as an important factor.
太阳黑子活动的年代际和长期变化对升温和降温云层模式的影响现在已被确认为一个重要因素。
That is, the sever uses 40 percent less power thanks to its efficient cooling system and unique form factor.
也就是，由于它具有高效率的冷切系统和独特形式的因素，它的能耗是其他用于Web 2.0环境下的服务器的40%。
During the producing process of slab caster, secondary cooling system is a very important factor which influences slab quality.
在板坯铸机的生产过程中，二次冷却制度是影响铸坯质量的重要因素。
Therefore, the cooling effect of the electromagnet is an important factor to keep the magnetic field strength not decreasing rapidly.
因此，电磁铁好的冷却散热效果是保持其场强不急剧减弱的重要因素。
Control of inner cooling generator cooling water quality in a definite extent is an important factor for ensuring generator safe operation.
控制发电机内冷却水水质在一定的范围内，是保证发电机安全运行的一个重要因素。
Combined with measured cooling curves, the TTP curve was used to predict the influence of quenching rate on the hardness of 7055 aluminum alloy by quench factor analysis method.
采用分级淬火的方法测定了7055铝合金的温度—时间—性能(ttp)曲线，并结合合金实际淬火冷却曲线通过淬火因子分析方法预测了合金的硬度。
It was felt at this point that the primary factor leading to disbonding was thermal shrinkage of the propellant during cooling.
据认为，在这一点，首要因素导致剥离是热的收缩推进剂冷却过程中。
This paper presented influence of factor on film cooling, enhanced heat transfer in tunnel and heat pipe cooling, how to apply and development for these technologies.
详细地阐述了对气膜冷却、内部强化换热以及热管冷却等的影响因素，目前的应用状况以及发展前景。
Cooling the sample from room temperature (290k) to liquid nitrogen temperature (77k) decreases the voltage noise by approximately a factor of two.
将样品从室温温度(290k)降低到液氮的温度(77k)，可以使得噪声电压减小大约一半。
Cooling distribution mode in refrigerated storage system is a main factor impacting the cost of refrigerated storage.
采用不同的供冷方式是影响冷库经济性的主要因素之一。
The results indicate, the main factor for grain refinement is cooling intensity, its polar odds is 57.946 and reliability is 99%. The next facts are preservation time and pouring temperature.
研究结果表明，冷却强度是晶粒细化的最主要因素，极差为57.946，可信度达到99%，其次是保温时间与浇注温度。
It showed that the heating and cooling temperature and rate was the factor effecting the process except for the blowing agent variety and the loading weigh.
实验研究显示，影响滚塑发泡工艺的因素除了发泡剂种类以及加入量，还有加热冷却温度、速度等等。
The main factor affecting the heat-exchanging performance of direct air cooling condenser is backflow or recirculation of the hot air resulted from the ambient strong wind.
影响空冷凝汽器换热性能的主要因素是环境大风所造成的热风回流或热风再循环。
According to the steps of optimal scheme and consideration factor about micro-turbine CCHP (combined cooling heating and power), several projects of CCHP are researched.
根据微燃机冷热电联供的优化配置步骤及考虑因素，对微燃机冷热电联供系统的几种方案进行了研究。
The experimental results during a cooling season indicate that the seasonal cooling performance factor of the system is 9.
经过一个供冷季的实验，该系统的季节供冷系数为9。
In single factor test, the influencing factor of tools wear was discussed, such as tool material, cooling conditions, cutting depth and feed speed.
以单因素实验法分别考察了刀具材料、冷却条件、切削深度、进给速度等对刀具磨损的影响规律。
Moreover, the experiment result shows that the temperature of the supply water is an important factor influencing the hearing or cooling capacity of the radiant floor.
同时得出辐射地板盘管供水温度是影响地板供冷热性能的重要因素的结论。
Moreover, some important system performance parameters were obtained, such as the cooling seasonal performance factor and the cold extraction rate per unit depth of borehole.
另外，还获得了一些重要的系统性能参数，如季节供冷系数、单位埋深取冷率。
If the work piece can be always kept cooling, cutting speed is not a key factor.
如果工件始终能保持冷却，切削速度不算关键。
Low ripple factor: it's of low interference to other equipments, forced air-cooling, automatically Shared load, low failure rate and high reliability.
纹波系数低，对其它设备干扰小；强制风冷式散热，负荷自动均分，故障率低，可靠性高。
In a hot strip mill, runout table cooling is the most critical factor to determine final mechanical properties of product it makes. It is...
在热连轧的过程模拟中，层流冷却是决定产品最终力学性能的最关键过程。
In a hot strip mill, runout table cooling is the most critical factor to determine final mechanical properties of product it makes. It is...
在热连轧的过程模拟中，层流冷却是决定产品最终力学性能的最关键过程。
应用推荐