用于各种铸铁合金铸铁钢与铸钢的焊接。
适用于碳钢、不锈钢、铜及其合金、铸钢的焊接。
Suitable for welding carbon steel, stainless steel, copper and its alloy, alloy steel and cast iron.
分析测定了中铬抗磨铸钢的流动性、缩孔率和铸造应力。
The casting fluidity, ratio of line contraction, casting stress and heat crack tendency were tested.
适用于碳钢，不锈钢，铜及其合金，合金钢，铸钢的焊接。
Suitable for carbon, steel, stainless steel, copper, titanium and cast iron welding.
介绍新研制的准贝氏体铸钢的化学成分、组织及性能特点。
The chemical composition, organization and properties of the newly developed quasi-Bainite cast steel are described.
测定并探讨了亚温处理后中锰铸钢的晶体学特性和物理特性；
The crystallographic and physical characteristic for the medium-manganese cast steels after the intercritical heat treatment have also been examined and discussed.
研究了经40%热变形后不同冷却速度下高碳铬铸钢的组织和性能。
The influence of cooling rate after 40 % hot deformation on structure and properties of high carbon chromium cast steel was studied.
铸钢的屈服强度是30K，而球墨铸铁的屈服强度更高，达到40 K。
Ductile Iron has a higher yield strength than cast steel 40k vs. 30k.
研究了在不同等温淬火温度热处理后高硅铸钢的显微组织与残余奥氏体量和材料断裂韧性间的关系。
The influence of austempering treatment on the microstructure, retained austenite and fracture toughness of high silicon cast steel has been studied.
对断裂起重机吊具zg270- 500铸钢的化学成分、硬度、显微组织、断口形貌等进行了检测和分析。
The chemical composition, hardness, microstructure and fracture morphology of ZG270-500 cast-steel of cracked lifting instrument were detected and analyzed.
试验结果表明，准贝氏体铸钢的各项性能指标均优于国内现行链轨架材质 性能，实体拉伸 性能达到进口铸件的 性能。
The results show that the meto-bainited cast steel values of various properties are advantageous over those present in use, and tensile prOperties are up to those of imported castings.
采用复合铸造法研制了一种芯部为低碳钢、外部为高铬铸钢的高耐磨碾齿，此碾齿用于玻璃厂破碎物料的粉碎机上，取得了良好的效。
By adopting a compound casting method, we have developed a kind of high wear resisting crushing bar, with low carbon steel interior, high chromium casting steel exterior.
泵体、泵盖的材质采用铸钢ZG230-450的较多，也可以采用球墨铸铁材质，两种材质对比后者的耐磨性和硬度以及耐温性要因为前者。
Pump cover material with steel ZG230-450 more, can also be used ductile iron, the latter two materials contrast of wear resistance and hardness and heat resistance to be because the former.
齿轮和齿轮托可以是铸铁或铸钢，可以有铸造或机加工的齿轮齿，取决于负载和应用环境。
The gears and gear brackets may be either cast iron or cast steel and may have cast or cut teeth, depending on the loads and the application.
应采用低氢焊条焊接厚钢板与铸钢件和高强度板间的连接。
Low hydrogen electrode to be used for welding thick steel plate to casting and high tensile plates.
铸钢空心球管节点是一种新型的铸钢节点形式。
Cast steel hollow spherical joint with tube is a new type of cast steel joint.
衬板、搅拌叶片均采用高硬度、高韧性的耐磨合金铸钢，使用寿命长。
Lining board, mixing blades adopts high hardness and high toughness wear-resistant steel and long service life.
通过正交试验，研究了各因素对真空实型铸造铸钢件涂料的透气性、干强度、剪切力、悬浮性的影响。
In this paper, the influence of various parameters on suspension shearing dry strength and permeability of EPC coating used on steel casting through right Angle test was studied.
木屑颗粒机是坚放大轴，大型铸钢轴承座，它的大轴承不承受任何压力，不容易坏，寿命长。
Wood pellet machine is a strong amplification shaft, large cast steel bearing seat, it's large bearings do not bear any pressure, not easy to bad, long life.
光可以使铸造车间的工人看到厚的铸钢件的内部。
The X-way allow a workman in a factory to look into a thick steel casting.
分析讨论了钙处理对连铸钢浇注性能的影响。
This paper analyzes the influence of calcium treatment on the castability of continuous casting molten steel.
KME在开发和生产连续铸钢用的铜模件方面树立起一座里程碑。
KME set milestones in the development and production of copper moulds for the continuous casting of steel.
我们必须避免机加工后在铸件商产生气孔。你们现在使用的铸钢是什么等级的？对于我方来说17级是最好的。
We need to avoid the air holes in the casting which appear after machining. What grade casting steel do you use?, for us grade 17 should be best.
我们必须避免机加工后在铸件商产生气孔。你们现在使用的铸钢是什么等级的？对于我方来说17级是最好的。
We need to avoid the air holes in the casting which appear after machining. What grade casting steel do you use?, for us grade 17 should be best.
应用推荐