介绍新研制的准贝氏体铸钢的化学成分、组织及性能特点。
The chemical composition, organization and properties of the newly developed quasi-Bainite cast steel are described.
测定并探讨了亚温处理后中锰铸钢的晶体学特性和物理特性;
The crystallographic and physical characteristic for the medium-manganese cast steels after the intercritical heat treatment have also been examined and discussed.
研究了经40%热变形后不同冷却速度下高碳铬铸钢的组织和性能。
The influence of cooling rate after 40 % hot deformation on structure and properties of high carbon chromium cast steel was studied.
铸钢的屈服强度是30K,而球墨铸铁的屈服强度更高,达到40 K。
Ductile Iron has a higher yield strength than cast steel 40k vs. 30k.
研究了在不同等温淬火温度热处理后高硅铸钢的显微组织与残余奥氏体量和材料断裂韧性间的关系。
The influence of austempering treatment on the microstructure, retained austenite and fracture toughness of high silicon cast steel has been studied.
对断裂起重机吊具zg270- 500铸钢的化学成分、硬度、显微组织、断口形貌等进行了检测和分析。
The chemical composition, hardness, microstructure and fracture morphology of ZG270-500 cast-steel of cracked lifting instrument were detected and analyzed.
这是因为硅使贝氏体铸钢在高应力冲击磨损下表现出不同的失效机制。
The reason is that the impact wear mechanism is different for low and high Si bainitic cast steels.
本文探讨了热变形高铬铸钢中颗粒状碳化物的形成。
This paper deals with the granular carbides formation from hot deformation in high chromium cast steel.
研究表明,该铸钢节点在设计荷载的作用下,具有足够的强度和刚度;
The present investigation indicates that the cast steel joint subjected to its design loads has sufficient strength and rigidity.
研究了回火工艺对新型贝氏体铸钢组织和性能的影响。
The influence of tempering process on microstructure and mechanical properties of new type bainite cast steel was studied.
研究了正火温度和回火温度对ZG310- 570铸钢组织和力学性能的影响。
Influences of normalizing temperature and tempering temperature on mechanical properties and microstructure of ZG310-570 cast steel were investigated.
研究了淬火温度和回火温度对ZG310- 510铸钢组织和力学性能的影响。
The Influence of quenching temperature and tempering temperature on mechanical properties and microstructure of ZG310-510 cast steel was studied.
本文主要介绍了卧式离心机铸造大直径铸钢套筒方法,讨论了降低套筒气孔和铸造裂纹的工艺措施。
Large diameter sleeve of steel casting by horizontal centrifugal casting machine has been introduced with discussion of technological measures of reducing pinhole and crack in sleeve.
KME在开发和生产连续铸钢用的铜模件方面树立起一座里程碑。
KME set milestones in the development and production of copper moulds for the continuous casting of steel.
分析讨论了钙处理对连铸钢浇注性能的影响。
This paper analyzes the influence of calcium treatment on the castability of continuous casting molten steel.
研究了高速纸机中具有闷头的空心铸钢辊结构的塑性极限和参数设计问题。
The plastic limit analysis and parametric design of a hollow cast steel roll with axle sleeve of the high-speed paper machine are studied.
对不同成分的耐热耐磨铸钢在相同热处理工艺条件下的组织及力学性能进行了一系列对比实验研究。
The microstructure and mechanical properties of heat-resistant and wear-resistant cast steel with different composition were studied under the same heat treatment condition by series of experiments.
研究了不同冷却介质对新型贝氏体铸钢组织和力学性能的影响。
The effects of different cooling medium on microstructure and mechanical properties of new type bainite cast steel were studied.
连铸钢水温度是连铸生产工艺的重要参数之一。
The molten steel temperature is one of important parameters of continuous casting process.
本文研究了钒对低碳铸钢组织和性能的影响。
The effect of vanadium on the structure and properties of low- carbon cast steel was studied in this paper.
研究了稀土元素及其添加量对高碳铬铸钢力学性能和耐磨性的影响。
Effects of re content on mechanical properties and abrasion resistance of high carbonic chromium cast steel were studied.
应采用低氢焊条焊接厚钢板与铸钢件和高强度板间的连接。
Low hydrogen electrode to be used for welding thick steel plate to casting and high tensile plates.
建立了高炉铸钢冷却壁的有限元模型,确定了冷却壁温度场模拟的初始条件和边界条件。
The finite element mould of the cast steel cooling stave of blast furnace was established and the initial conditions and boundary conditions were determined.
研究了稀土变质剂对超低碳铸钢晶粒尺寸的影响。
Influence of RE modifier on as cast grain size of super low carbon cast steel was studied.
用扫描电镜分析研究了铁基合金涂层对车轮铸钢材料抗热疲劳损伤机制的影响。
The mechanism of Fe-based alloy coating for thermal fatigue damage resistance of wheel cast steel was analyzed by SEM.
齿轮和齿轮托可以是铸铁或铸钢,可以有铸造或机加工的齿轮齿,取决于负载和应用环境。
The gears and gear brackets may be either cast iron or cast steel and may have cast or cut teeth, depending on the loads and the application.
齿轮和齿轮托可以是铸铁或铸钢,可以有铸造或机加工的齿轮齿,取决于负载和应用环境。
The gears and gear brackets may be either cast iron or cast steel and may have cast or cut teeth, depending on the loads and the application.
应用推荐