文中研究的是球状石墨铸钢新材料。
A new cast steel materials with spheroidal graphite has been studied.
铸钢，青铜，铸铁和合金阀门。
后来又说2平炉电炉生产铸钢件。
Later added 2 open hearth furnaces for producing steel castings.
铸钢锁轴在加工螺纹时轴杆端头断裂。
Casting steel container rotating lock axle rod-head fracture in machining screw.
铸钢阀门锤击手轮，阀座环，楔形闸板。
大部分浇铸成成品形状的钢是中碳铸钢。
Most of the steel cast into finished shapes is medium carbon cast steel.
高水平的铸钢件生产能力。
分析讨论了钙处理对连铸钢浇注性能的影响。
This paper analyzes the influence of calcium treatment on the castability of continuous casting molten steel.
铸钢空心球管节点是一种新型的铸钢节点形式。
Cast steel hollow spherical joint with tube is a new type of cast steel joint.
连铸钢水温度是连铸生产工艺的重要参数之一。
The molten steel temperature is one of important parameters of continuous casting process.
光可以使铸造车间的工人看到厚的铸钢件的内部。
The X-way allow a workman in a factory to look into a thick steel casting.
本文探讨了热变形高铬铸钢中颗粒状碳化物的形成。
This paper deals with the granular carbides formation from hot deformation in high chromium cast steel.
研究了不同的淬火温度对高硼铸钢冲击耐磨性的影响。
The Influence of quenching temperature on wear resistance of high boron casting steel was investigated.
应采用低氢焊条焊接厚钢板与铸钢件和高强度板间的连接。
Low hydrogen electrode to be used for welding thick steel plate to casting and high tensile plates.
选择球墨铸铁的一个重要的原因在于球墨铸铁比铸钢成本低。
Select one of the major reasons cast iron ductile iron is lower than the cost of steel.
以材质划分为：碳钢、铸钢、合金钢、不锈钢、铜、铝合金等。
The material is divided into: carbon steel, cast steel, alloy steel, stainless steel, copper, aluminum alloy.
本文主要介绍了使用计算机模拟进行实际铸钢件工艺设计方法。
This paper focuses on the practical approach of rigging steel castings using computerized casting simulation.
KME在开发和生产连续铸钢用的铜模件方面树立起一座里程碑。
KME set milestones in the development and production of copper moulds for the continuous casting of steel.
研究表明，该铸钢节点在设计荷载的作用下，具有足够的强度和刚度；
The present investigation indicates that the cast steel joint subjected to its design loads has sufficient strength and rigidity.
衬板、搅拌叶片均采用高硬度、高韧性的耐磨合金铸钢，使用寿命长。
Lining board, mixing blades adopts high hardness and high toughness wear-resistant steel and long service life.
这是因为硅使贝氏体铸钢在高应力冲击磨损下表现出不同的失效机制。
The reason is that the impact wear mechanism is different for low and high Si bainitic cast steels.
对铸钢15 - 5ph法兰盘表面抛丸后皱皮的产生原因进行了分析。
Cause of the surface wrinkling of flange made of 15-5ph cast steel was studied.
介绍了湿型铸造中、小型铸钢件易产生的缺陷及防止缺陷所采取的工艺措施。
Defects in green casting process of small and middle steel_castings and the technical measures for protecting from defects are introduced.
用扫描电镜分析研究了铁基合金涂层对车轮铸钢材料抗热疲劳损伤机制的影响。
The mechanism of Fe-based alloy coating for thermal fatigue damage resistance of wheel cast steel was analyzed by SEM.
设计了一种中锰铸钢锤头材质，其在非强冲击条件下具有较好的加工硬化效果。
Designed a medium manganese cast steel used to making hammer, which has good work-hardness under non severe impact condition.
悬浮浇注增加铸钢凝固期间的冷却强度，缩短凝固时间，增加体积凝固的倾向性。
In suspension pouring process the increase of cooling intensity during the solidification period will increase the tendency of volume solidification and decrease the solidification time.
齿轮和齿轮托可以是铸铁或铸钢，可以有铸造或机加工的齿轮齿，取决于负载和应用环境。
The gears and gear brackets may be either cast iron or cast steel and may have cast or cut teeth, depending on the loads and the application.
齿轮和齿轮托可以是铸铁或铸钢，可以有铸造或机加工的齿轮齿，取决于负载和应用环境。
The gears and gear brackets may be either cast iron or cast steel and may have cast or cut teeth, depending on the loads and the application.
应用推荐