Three dimension finite element method is used to calculate the stress state of the cantilever during each construction stage.
因此对桥悬臂施工过程进行了三维有限元计算，分析了各个施工阶段的应力状态。
Finite element mechanical model of moving crossbeam is set up for analyzing three dimension finite element intensity of this structure.
并建立了活动横梁的有限元力学模型，对该结构进行了三维有限元强度分析。
Three dimension finite element simulation and analysis of shoulder is a valuable mechanical method for research on biomechanics theory related to humerus fracture.
肱骨骨折的三维限元模拟和分析是究与骨折相关的力学原的非常有价值的方法。
This paper developed a three dimension finite element model to analyze stress distribution on residual limb of crus under lumped loads with different displacement constraint conditions.
通过建立三维线性有限元模型来分析在集中载荷作用下小腿肢体残端的应力分布，且分析了不同边界条件对肢体残端应力分布的影响。
Based on the dynamic characteristics obtained with three dimension finite element method, the reduced mechanical model and parameters of lift ship structure can be modified and obtained.
利用三维有限元方法计算的结构动力特性和简化结构动力特性相等的原则修正升船结构简化力学模型，并确定了等效的升船机简化结构模型和系统参数。
For the multiphase flow measuring system on-line based on three dimension finite element method (3d FEM), the capacitance-based multiphase flow which is connected to the oil pipeline is a column.
基于三维有限元法的在线多相流测量系统，所接入输油管道的电容式多相流为圆柱形。
This paper introduces how to establish Three-dimension finite element model to solute low frequency sound transfer function in small-enclosed room.
文中详细介绍了如何建立用于求解小尺度封闭空间低频声传递函数的三维有限元素模型。
The strength of oblique edge shear is analyzed by three dimension finite-element method, through which provides scientific basis for increasing shearing capability.
用有限元法对剪切机机架强度进行分析，为提高剪切机剪切能力提供了理论依据。
In this paper, finite element method of a quasi-three dimension problem was described in detail, where the stress-strain relations are linear or nonlinear.
本文详细地描述了准三维问题的有限元法，包括应力应变关系是线性的情况和应力应变关系是非线性的情况。
In this thesis the heat transfer theory and the finite element method are used to simulate the two dimension temperature field and the three dimension temperature field.
本文应用传热学基本原理和有限元基本方法，完成了二维、三维导热温度场的有限元数值模拟。
Three-dimension analysis of solid rocket motor grain was presented based on incompressible and nearly incompressible viscoelastic finite element method.
基于不可压和近似不可压粘弹性有限元法，对固体火箭发动机药柱进行了三维分析。
The influencing factors to suspending rigid plate are investigated by three-dimensional finite element analysis. The investigation places emphasis on the contribution of the dimension of suspending.
通过三维有限元分析，考察了刚性路面脱空的影响因素，重点考察脱空的几何尺寸对弯沉值的影响。
In this paper, a three-dimension concrete block finite element model has been established, then the factors affecting the performance of concrete masonry are analyzed.
本文通过建立一个三维灌芯混凝土砌块棱柱体有限元模型，进行非线性计算，分析了影响混凝土砌体性质的因素。
Three-dimension finite element model is built according to the actual structural characteristic of suspension pipe bridge.
按照悬索式管桥的实际结构特点，建立了三维有限元模型。
At low flow attenuation performance of semi-active muffler was computed respectively by using theoretical formula and three-dimension finite element method.
低速气流时，分别进行了半主动消声器的消声性能理论计算和三维有限元法数值计算。
The CAE technology and PATRAN finite element software were used in three-dimension simulation and analysis for three axis turntable frame system.
三轴转台框架系统的三维模拟与分析，采用CAE技术，使用PATRAN有限元软件。
Based on three-dimension finite element model, transient temperature field in nozzle was calculated.
基于三维有限元模型，计算了喷管的瞬时温度场。
The cross wedge rolling deformation process of shaft parts with eccentric section was simulated with three-dimension finite element soft LS-DYNA by using elastic-plastic finite element method.
利用三维弹塑性有限元软件L S- DY NA对一种典型偏心轴类零件楔横轧成形进行了数值模拟，分析了其成形过程、应力应变场分布及工艺特点。
Three-dimension isothermal flows in the metering section of reciprocating screw injection machines are simulated using the finite element package POLYFLOW.
使用Poly flow软件对熔融物料在往复螺杆式注塑机螺杆头部计量段中的三维等温流场进行了数值模拟。
Three-dimension isothermal flows in the metering section of reciprocating screw injection machines are simulated using the finite element package POLYFLOW.
使用Poly flow软件对熔融物料在往复螺杆式注塑机螺杆头部计量段中的三维等温流场进行了数值模拟。
应用推荐