Affix using one of the crank arm fixing bolts.
词缀使用其中的一个曲柄臂固定螺栓。
The crank is an offset section of the crankshaft.
曲柄是曲轴的偏置部分。
The crank connecting rod is adjustable in length.
曲柄连接杆的长度是可调节的。
The crank is an offset section of the crankshaft .
曲柄是曲轴的偏置部分。
And then starting to turn the crank on the algebra.
然后开始代数变换。
The corrector is a modification of the crank-nicolson equation.
校正式是克兰克-尼科尔森方程的修改式。
The corrector is a modification of the Crank - Nicolson equation.
校正式是克兰克·尼科尔森方程的修改式。
And then we can write, if we turn the crank, we get an equation that looks like this.
我们可以这么写，得到这样子的形式。
This method can also be used to predict the failure probability of the crank pin.
利用这种设计计算方法还可以预测曲柄销的失效概率。
Casting defects, especially porosity, will reduce fatigue strength of the crank-shaft.
铸造缺陷，尤其是铸造缩松，降低了曲轴的疲劳强度。
A new method of modeling of diesel engines is adopted based on the crank-angle domain.
研究了基于曲轴角度域闭环辨识柴油机模型的建模方法。
If we were to turn the crank, we'd say, oh, I've got to write down all my rate laws here.
如果我们要等式变换，我会说，哦，我要写下所有的速率定律。
Effect of change of mean angular velocity of the crank on stability of SCWC was analyzed.
其后，分析了爬楼梯轮椅曲柄平均角速度的改变对其稳定性的影响。
Revolves, canned, the V-belt pulley organization, the CAM gear, the crank slide, the bevel gear.
旋转、罐装、槽轮机构、凸轮机构、曲柄滑块、锥齿轮。
On some pumpers, the rotary counterbalance can be adjusted by shifting the position on the crank arms.
在某些抽油机上，旋转平衡块可由改变其在曲柄臂上的位置进行调整。
By golden section method the program on optimal design of the crank and slider mechanisms is worked out.
用黄金分割法编制了曲柄滑块机构的优化设计程序，可以解决六类优化设计问题。
Dial gauge with universal dial gauge bracket must be screwed to the cylinder block and placed against the crank arm.
百分表及通用百分表托架必须通过螺钉固定在气缸体上，位置与曲轴臂相对。
Torque is calculated by multiplying the push by the crank offset, or the distance of the push from the rotating shaft.
扭矩以推力与曲柄偏心距或旋转轴心至推力作用点的距离相乘计算。
You set your initial figures by sliding knobs along the side of the cylinder, then turn the crank to compute the results.
你可以滑动圆柱体边上的滑钮设定初始值，然后转动手柄来计算结果。
The crank reference pulse originates from a variable reluctant pickup which senses a projection on the engine's flywheel.
曲柄参考点脉冲信号由一个变磁阻传感器产生，它从发动机飞轮上的突起感受信号。
When I was there early enough, I got to help prepare the meal, shelling the beans or turning the crank on the ice-cream maker.
要是到巴迪家早一些的话，我也一块儿帮忙做饭，不是剥豆子，就是摇冰淇淋机的把儿。
In the crank and rocker mechanism, when the rocker acts as the driving link, there will be two dead points in one working cycle.
在曲柄摇杆机构中，当以摇杆为原动件时，工作一个循环以后，直观看出有两次死点位置出现。
The undersigned did deem that if the non-parallelism of the crank pin exceeds permissible limitation, crank pin and bearing were caused to be burnt.
下列署名的验船师认为曲柄肖不平行度超过允许值时会导致曲柄肖和轴承烧坏。
Practical working charts for the crank balanced position of two types of units, which will give a reference to the designers and operators, are offered.
并对两种机型提出了曲柄平衡位置工作实用图表，可供前置式抽油机设计和使用者参考。
This paper described work principle and structure design of side cut punch composite mold and assembly testing requirements using the crank press machine.
介绍了在曲柄压力机上切边冲孔的复合模结构设计、工作原理及装配和调试要求等。
Aiming at the problem of on-line calculation to the temperature field for turbine rotor, the Crank-Nicolson finite-difference calculation model was given.
针对汽轮机转子温度场的在线求解问题，给出了克兰克·尼科尔森差分计算模型。
With the earthing switch closed, insertion of the withdrawable part towards the service position must be blocked after only two clockwise turns of the crank.
如果接地开关处于合闸状态，手车向工作位置的操作必须被机械联锁锁定。
With the earthing switch closed, insertion of the withdrawable part towards the service position must be blocked after only two clockwise turns of the crank.
如果接地开关处于合闸状态，手车向工作位置的操作必须被机械联锁锁定。
应用推荐