And then starting to turn the crank on the algebra.
然后开始代数变换。
You set your initial figures by sliding knobs along the side of the cylinder, then turn the crank to compute the results.
你可以滑动圆柱体边上的滑钮设定初始值,然后转动手柄来计算结果。
When I was there early enough, I got to help prepare the meal, shelling the beans or turning the crank on the ice-cream maker.
要是到巴迪家早一些的话,我也一块儿帮忙做饭,不是剥豆子,就是摇冰淇淋机的把儿。
The crank is an offset section of the crankshaft.
曲柄是曲轴的偏置部分。
The crank is an offset section of the crankshaft .
曲柄是曲轴的偏置部分。
The corrector is a modification of the crank-nicolson equation.
校正式是克兰克-尼科尔森方程的修改式。
This method can also be used to predict the failure probability of the crank pin.
利用这种设计计算方法还可以预测曲柄销的失效概率。
The equation for calculating minimum tightening torque on the crank pin nut is given.
给出了曲柄销联接螺母的最小拧紧力矩计算公式。
Casting defects, especially porosity, will reduce fatigue strength of the crank-shaft.
铸造缺陷,尤其是铸造缩松,降低了曲轴的疲劳强度。
Effect of change of mean angular velocity of the crank on stability of SCWC was analyzed.
其后,分析了爬楼梯轮椅曲柄平均角速度的改变对其稳定性的影响。
On some pumpers, the rotary counterbalance can be adjusted by shifting the position on the crank arms.
在某些抽油机上,旋转平衡块可由改变其在曲柄臂上的位置进行调整。
By golden section method the program on optimal design of the crank and slider mechanisms is worked out.
用黄金分割法编制了曲柄滑块机构的优化设计程序,可以解决六类优化设计问题。
The upper is communicated with the gas chamber and the lower is linked with the rocker through the crank.
上端与气室相连,下端通过曲柄与摇杆相连。
The load applied on the crank pin of a beam pumping unit and the failure patterns of the pin are analyzed.
分析了游梁式抽油机曲柄销所受载荷及失效形式。
TDC (top dead center) - the position of the crank and piston when the piston is farther away from the crankshaft.
(上止点)-当活塞离曲轴最远时,曲柄和活塞的位置。
Dial gauge with universal dial gauge bracket must be screwed to the cylinder block and placed against the crank arm.
百分表及通用百分表托架必须通过螺钉固定在气缸体上,位置与曲轴臂相对。
Through an example, it is demonstrated that the dynamic response can be reduced by adjusting the length of the crank.
实例计算的分析结果表明:选择适当的变化规律,改变曲柄长度,可以降低机构的动态响应。
Torque is calculated by multiplying the push by the crank offset, or the distance of the push from the rotating shaft.
扭矩以推力与曲柄偏心距或旋转轴心至推力作用点的距离相乘计算。
The utility model has practicability in the connection of the crank connecting rod component of the motorcycle engine.
它在摩托车发动机曲轴连杆组件的连接中具有极大的实用价值。
A mechanical model for calculating the strength of the crank pin on pumping units is established by a rotary coordinate.
采用动坐标系建立了曲柄销强度计算的力学模型。
The bevel gears and the crank shafts are totally enclosed in oil chamber and require no attention, except periodical checks.
锥齿轮和曲柄轴都在油室内,除定期检查外,无需专门关注。
The author holds further that the crank pin rotation on conventional pumping units should be assigned in counterclockwise...
作者还认为,常规式抽油机的曲柄旋转方向应规定为逆时针,并建议研制可调相位角的曲柄平衡重。
In the crank and rocker mechanism, when the rocker acts as the driving link, there will be two dead points in one working cycle.
在曲柄摇杆机构中,当以摇杆为原动件时,工作一个循环以后,直观看出有两次死点位置出现。
The optimal positions of the vibration sensor should be located on both sides of the crank-shaft bearing or bottom of the engine.
传感器最佳位置是在曲轴轴承正对的发动机两侧或油底壳处。
The prime motor rotates in a fixed direction and the alternating motion of the carrier bar is accomplished by the crank-rocker mechanism.
电动机单向旋转,用曲柄摇杆机构换向,实现悬点的往复直线运动。
The utility model relates to the structural improvement of the crankshaft of brick presses and particularly to that at the crank of crankshaft.
本实用新型涉及一种压砖机曲轴的结构改进,尤其是曲轴的曲柄 处的结构改进。
Using the two - level fuzzy comprehensive theory for the realibilty testing of the crank pin in the non - beam pump is discussed in this article.
利用二级模糊综合评判原理对无游梁式抽油机曲柄销的可靠度进行预测。
Using the two - level fuzzy comprehensive theory for the realibilty testing of the crank pin in the non - beam pump is discussed in this article.
利用二级模糊综合评判原理对无游梁式抽油机曲柄销的可靠度进行预测。
应用推荐