The optimal burden ratio of sintered chromite is 60-65%.
冶炼中烧结铬矿的搭配比例以60—65%为佳。
Is China's largest sintered NdFeB magnet production, one.
是中国最大的烧结钕铁硼磁体生产企业之一。
This will then be sintered in a suitable atmosphere to yield the required product.
然后放入合适的环境中烧结成所需产品。
China has still a large number of residential construction using sintered clay brick.
中国仍然有大量的住宅建筑使用烧结粘土砖。
The microstructure and mechanical properties of the sintered compact were investigated.
研究了烧结体的显微组织和力学性能。
Sintered properties of the oil pump gears and part to part consistency are also reported.
还报告了油泵齿轮烧结后的性能和零件间性能的均一性。
The characteristics of metal powder for producing the sintered metallic filter was studied.
研究了生产烧结金属过滤器的原料粉末的性能特征。
Optimize the dielectric properties of low temperature sintered microwave dielectric ceramics.
优化低温烧结微波介质陶瓷介电性能。
Study has been made on preparation process of sintered brick with 80% flay ash and plasticizer.
对掺塑化剂,粉煤灰掺量达80%的烧结砖的制备工艺进行了研究。
The effect of raw material powder on the sintered properties of Boron Carbide was investigated.
研究了原料粉末对碳化硼陶瓷常压烧结性能的影响。
The developing situations of filtration technology utilizing sintered metal media was introduced.
介绍了使用烧结金属过滤介质的过滤技术的进展情况。
The outer skin is made of sintered glass mosaics depicting a variety of digitally generated patterns.
外皮是由烧结的马赛克玻璃描绘出的各种数字化图案。
Thee mixture of tungsten carbide and cobalt powder is pressed into the required shape and then sintered.
碳化钨和钴粉末的混合物被挤压成所需形状后进行烧结。后进行烧结。
In the non sintered cement, the kind and amount of stimulator determines the reaction speed and quality.
在无熟料水泥中,激发剂的种类和数量是决定其水化反应速度和品质的关键。
Powder forged parts generally are not as close to final size or shape as cold pressed and sintered parts.
粉末锻造零件通常不像冷挤压和烧结零件那样接近最终尺寸或形状。
In non sintered cement, the hydration speed and quality are determined by kind and amount of the stimulator.
在无熟料水泥中,激发剂的种类和数量是决定其水化反应速度和品质的关键。
Also the result shows that, as sintered in reducing atmosphere, the dielectric loss of the material increase.
研究的结果还表明,由于在还原气氛中烧结,材料的介电损耗上升。
This paper introduces the industrial-scale experiment of carbon ferrochrome manufacture with sintered chromite.
介绍了使用烧结铬矿冶炼炭素铬铁的工业性试验情况。
The dense ceramic products can be obtained using sintered magnesite as raw materials and alcohol as mixing medium.
以酒精力混合介质,烧结镁砂为原料获得致密的陶瓷烧结制品是可行的。
The application of powder injection molding in the production of bonded magnets and sintered magnets were discussed.
讨论了粉末注射成形在粘结磁体生产中的应用和烧结磁体研究开发的现状。
However, the high temperature sintered body strength slightly lower, mainly for the use of low temperature environment.
但是烧结体的高温强度稍低,主要用于使用温度较低的环境。
Adding middle grade sintered magnesia powder can enlarge the line ratio and porosity after high temperature treatment.
中档镁砂粉的添加使浇注料高温处理后的线变化率增大和气孔率增加。
The dynamic process of bottom-water bypassing interbed and fleeing upward is simulated by using sintered planner models.
采用烧结的平面物理模型,实验模拟底水绕过上窜夹层的动态过程。
The exceptional tool performance of sintered carbides results from their very high hardness and high compressive strength.
硬质合金材料的出色之处来源于它们非常高的硬度和耐压强度。
The present paper has briefly described the basical technologies of sintered high speed steel products and their properties.
本文简述烧结高速钢制品的基本生产工艺及其性能。
It was found that increasing laser power or decreasing scan speed leads to higher sintered density and structural homogeneity.
结果表明,适当增加激光功率或减小扫描速率能改善烧结致密度及组织连续性。
With the two methods the homogenous green bodies without density gradient and high density sintered ceramic bodies can be gained.
利用这两种成型技术可以获得均匀、无密度梯度的近净尺寸坯体和致密陶瓷制品。
As an important procedure for sintered and bonded magnets, orienting compression has direct influence on the property of the magnet.
取向成型是烧结和粘结磁体的一道重要工序,对最终磁体的性能有直接影响。
It shows that ceramic material with good performance can be obtained by sintered technique to change crystal phase in ceramics product.
这表明,可以通过烧结工艺改变陶瓷制品中的晶相,从而获得性能优良的陶瓷材料。
It shows that ceramic material with good performance can be obtained by sintered technique to change crystal phase in ceramics product.
这表明,可以通过烧结工艺改变陶瓷制品中的晶相,从而获得性能优良的陶瓷材料。
应用推荐