• The right choice and control of the sintering atmosphere is very important for the properties of sintered components.

    烧结气氛的正确选择及其控制对烧结后部件的性能至关重要。

    youdao

  • It was found that increasing laser power or decreasing scan speed leads to higher sintered density and structural homogeneity.

    结果表明,适当增加激光功率或减小扫描速率能改善烧结致密度及组织连续性。

    youdao

  • As an important procedure for sintered and bonded magnets, orienting compression has direct influence on the property of the magnet.

    取向成型是烧结和粘结磁体的一道重要工序,对最终磁体的性能有直接影响。

    youdao

  • The results indicated that using laser surface hardening could remarkably improve the wear resistance of Febased sintered materials.

    结果表明,经宽带激光表面处理后,铁基烧结材料的耐磨性显著提高。

    youdao

  • With the increasing demand for the cooling of electronic chips, the micro heat pipe with the sintered wick has become an ideal heat radiator.

    目前电子芯片对散热的要求越来越高,烧结式吸液芯微热管已经成为电子芯片理想的散热元件。

    youdao

  • The optimal burden ratio of sintered chromite is 60-65%.

    冶炼中烧结铬矿的搭配比例以60—65%为佳。

    youdao

  • This will then be sintered in a suitable atmosphere to yield the required product.

    然后放入合适的环境中烧结成所需产品。

    youdao

  • The microstructure and mechanical properties of the sintered compact were investigated.

    研究了烧结体的显微组织和力学性能。

    youdao

  • The nonlinear magnetic property of low temperature sintered Y-type ferroxplana was reported.

    介绍了低温烧结Y型平面六方铁氧体的非线性磁性能。

    youdao

  • The results indicate that sintered body consists of different phases from surface to centre.

    结果表明,烧结体从表层到心部相组成不同。

    youdao

  • Optimize the dielectric properties of low temperature sintered microwave dielectric ceramics.

    优化低温烧结微波介质陶瓷介电性能。

    youdao

  • Study has been made on preparation process of sintered brick with 80% flay ash and plasticizer.

    对掺塑化剂,粉煤灰掺量达80%的烧结砖的制备工艺进行了研究。

    youdao

  • The effect of raw material powder on the sintered properties of Boron Carbide was investigated.

    研究了原料粉末对碳化硼陶瓷常压烧结性能的影响。

    youdao

  • The La-doped PZN-PZT ceramics and their powders were fabricated using solid state sintered technology.

    采用固相烧结法合成了不同镧掺杂量的PZN - PZ t压电陶瓷和粉体。

    youdao

  • In the non sintered cement, the kind and amount of stimulator determines the reaction speed and quality.

    在无熟料水泥中,激发剂的种类和数量是决定其水化反应速度和品质的关键。

    youdao

  • Powder forged parts generally are not as close to final size or shape as cold pressed and sintered parts.

    粉末锻造零件通常不像冷挤压和烧结零件那样接近最终尺寸或形状。

    youdao

  • In non sintered cement, the hydration speed and quality are determined by kind and amount of the stimulator.

    在无熟料水泥中,激发剂的种类和数量是决定其水化反应速度和品质的关键。

    youdao

  • This paper introduces the industrial-scale experiment of carbon ferrochrome manufacture with sintered chromite.

    介绍了使用烧结铬矿冶炼炭素铬铁的工业性试验情况。

    youdao

  • Adding middle grade sintered magnesia powder can enlarge the line ratio and porosity after high temperature treatment.

    中档镁砂粉的添加使浇注料高温处理后的线变化率增大和气孔率增加。

    youdao

  • The dynamic process of bottom-water bypassing interbed and fleeing upward is simulated by using sintered planner models.

    采用烧结的平面物理模型,实验模拟底水绕过上窜夹层的动态过程。

    youdao

  • The phase structure and high toughness of powder sintered biphase stainless steel and after its ageing have been studied.

    研究了粉末烧结双相不锈钢及其时效后的相结构和强韧性。

    youdao

  • The exceptional tool performance of sintered carbides results from their very high hardness and high compressive strength.

    硬质合金材料的出色之处来源于它们非常高的硬度和耐压强度。

    youdao

  • The transitional phase appeared when two ferroelectric powders with different Curie point were mixed and sintered together.

    具有不同居里点的两种铁电体粉末在共烧时会产生过渡相。

    youdao

  • The present paper has briefly described the basical technologies of sintered high speed steel products and their properties.

    本文简述烧结高速钢制品的基本生产工艺及其性能。

    youdao

  • With the two methods the homogenous green bodies without density gradient and high density sintered ceramic bodies can be gained.

    利用这两种成型技术可以获得均匀、无密度梯度的近净尺寸坯体和致密陶瓷制品。

    youdao

  • Results show that the sintered properties of the composites are associated with their compositions and the sintering temperatures.

    结果表明:该体系材料烧结性能与试样组成和烧成温度有关。

    youdao

  • In the hot repressing of the powder sintered preforms, the increasing forging force increases its densities at a constant temperature.

    在相同温度下进行粉末烧结体热复压,锻造力的增加往往使锻造密度也增加。

    youdao

  • It shows that ceramic material with good performance can be obtained by sintered technique to change crystal phase in ceramics product.

    这表明,可以通过烧结工艺改变陶瓷制品中的晶相,从而获得性能优良的陶瓷材料。

    youdao

  • Conclusion Porous plates developed by making use of sintered powder technology could meet requirements of performance of water sublimator.

    结论采用粉末烧结技术研制的多孔板的特性满足水升华器的性能要求。

    youdao

  • Conclusion Porous plates developed by making use of sintered powder technology could meet requirements of performance of water sublimator.

    结论采用粉末烧结技术研制的多孔板的特性满足水升华器的性能要求。

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定