The result of this shearing force is to push the endoplasm forward.
这种剪切力作用的结果是推动内质向前。
Decreasing the particle size is usually conducted by applying a shearing force.
通常使用剪切力减小颗粒粒度。
The distribution of storey shearing force in frame-shear wall structure is discussed.
讨论了框剪结构在弹性和弹塑性工作状态下楼层剪力的分配机理。
However, under cyclic shearing force, brick masonry also undergoes evident hysteretic behaviour.
其实，砌体在周期性剪力作用下具有显著的滞回性质。
This article introduces how to make the band saw sensor of measured shearing force and its structure.
文中介绍了带锯切削力传感器的结构、制做方法。
The firmness, elasticity and shearing force of bread by rheometer during storage of bread were determined.
采用流变仪测定了面包在贮存期间的硬度、弹性及剪切力的变化。
Reasonable design of shear connector need availably control of horizontal shearing force between steel webs.
合理地设计抗剪连接件需要有效地控制钢腹板和混凝土材料之间的水平剪切力。
It is concluded that exerting the vibration when shearing, the shearing force and work will be obviously decreased.
结果表明：剪切时施加振动，会显著减小剪切力和剪切功。
Interactions among Oxial force, fending moment and shearing force are considered in the generalized yield function.
所采用的广义屈服函数中考虑了轴力、弯矩、剪力、扭矩的交互作用。
The longitudinal shearing force of running vehicles (LSFRV) is computed and the mechanism of pavement damage studied.
研究了行车纵剪力计算与损伤路面的机理。
There was positive correlation between shearing force and acid detergent lignin, hemicellulose and cellulose content.
剪断力随着酸性洗涤木质素、半纤维素和纤维素含量增加而增大，呈正相关关系。
The vertical pressure acted on rod is also studied. Its size and distribution rules confirm the shearing force theory.
对拉杆上所受的垂直压力进行了研究，其大小及分布规律有力地验证了剪力理论。
The shearing force wall which may affect collapse of building was shut off in advance on the basis of safe construction.
在不影响施工安全的前提下，对有可能影响楼房倒塌的剪力墙做了必要的预处理。
Meanwhile, in the superposition beat shearing force wall, the precast block and the core concrete part can work cooperatively.
叠合板式剪力墙中，预制板与核心混凝土部分能够较好地共同工作。
Abstract: This experiment was conducted to study the correlations between shearing force and nutrient contents of cotton stem.
摘要本试验旨在研究棉秆剪切力与营养成分含量之间的相关关系。
Additionally, it is possible to generate shearing force by some factors like the change of temperature or support displacement.
另外，温度、支座位移等因素也可能引起较大的面内剪力。
Therefore, the retaining buttons can bear larger load so that they will not break or be damaged because of large shearing force.
因此，保留按钮可以承受较大的负载，使他们不会中断，或因剪切力的大破坏。
For shearing force lag in outer tube, sections of beams in outer tube are augmented and sections of corner columns are adjusted.
针对外筒的剪力滞后，设计中尽量增大了外框筒裙梁的截面高度，并适当调整了角柱截面。
Through vast amount of theoretical calculations that the suitable linking degree of shearing force in engineering, design is probed.
通过大量理论计算，探讨工程设计中合适的剪力连接度。
The theoretical design and calculation of the circular-section I-shaped beam shearing force sensor have been emphasized in this paper.
本文着重论述了圆截面工字梁剪力传感器的理论设计与计算。
Knurling machine is the key equipment to increase shearing force of the combined profiles of thermal barrier strips and aluminum alloy.
开齿机是提高隔热条与铝合金组合型材剪切力的关键设备。
Then the action principle of shearing force has been surveyed, and the distribution law of connected parts in the structures was raised.
对抗剪工作机理进行探讨，提出了连接件在结构中的分布规律。
If the compressive and tensile forces are greater enough to make the layers of the material slide upon each other, a shearing force results.
如果压缩力和拉伸力足够大，使得材料的各层次间相互滑移，那么就产生了剪切力。
Using double transmission, double knife panel and add the water power shearing force. Which will urge the waste paper to accelerate hydration.
采用双套传动，双刀盘增加了水力剪切力，促使废纸加速水比、碎解。
The study results prove the advantages of groove guided roiling shear in improving the quality of shearing and reducing the peak shearing force.
并对该软件系统进行了可行性验证，通过验证结果，证明了辊轮导槽导向式装置在克服剪切力峰值和提高剪切质量等方面的优越性。
It features recirculating mixing, obviously decreasing shearing force of the stirring, percolating oxygen supply and raising the cell cultivating result.
它有效克服了现有技术的缺点，具有环流混合、显著减小搅拌剪切力、渗透供氧、提高细胞培养效果和拓宽应用范围之特点。
The flume experiment shows that the low strength soil in the action of wave shearing force would slide, as the result, strong erosion happens on the bottom.
通过水槽实验发现，底床强度弱区的土体在波浪剪切力作用下，会发生整体滑动现象，造成床面的剧烈侵蚀。
Shearing force, which is necessary in device inspection, increases with the die dimension, and challenges the reliability of back metallization process greatly.
剪切力是器件考核的基本项目，随管芯面积的增大而增大，这就对背面金属化可靠性提出了较高的要求。
The natural frequency of taper and top plate taper beam are calculated in detail, and the effect of shearing force in beam on the natural frequency is discussed.
具体地计算了圆锥形悬臂杆及平头圆锥悬臂杆的固有频率值，同时，讨论了剪力对固有频率的影响。
In order to make strength analysis, analog conversion method was used to obtain the shearing force, which could not be determined on the shearing machine directly.
为了进行强度分析，文中在剪切力的获取上采用了模拟转换方法，从而解决了在剪切机上不能直接得到剪切力的困难。
应用推荐