Secondly, the stability of designed AFCS is analyzed and an amalgamation control mode of damper and stability augmentation control system is put forward in the paper.
其次，文中对设计的飞控系统进行了稳定性分析，提出阻尼器与增稳控制系统相融合的控制方式。
In order to exert policy efficiency, in this paper designed basic framework of protecting environment, and put forward the idea about the design of assorting policy.
为了能最充分地发挥环境政策效应，本文设计了环境政策的基本框架，并提出了分类环境政策设计的思路。
A novel method that USES the harmonic back EMF signal to extract the rotor position is put forward, and a new position sensor merged into an organic whole with the motor is designed.
提出了一种利用谐波反电势信号实现电机转子位置检测的新方法，设计了与电机一体化的新型位置传感器。
A new method to produce and pick-up optical label using phase modulation was put forward. The principle of this method was analyzed and experiment principle architave was designed.
本文提出了一种用相位调制实现光标记产生和提取的新方法，分析了这种方法的原理，设计出产生和提取光标记的试验框图。
At last we proposed about study new community how to draw lessons from old community space designed, and put forward another research problem for other researchers.
最后提出了关于进一步研究新社区如何借鉴老社区交往空间设计的探讨，为自己及其他研究人员提出了另一个研究问题。
The test platform which is designed and implemented in this paper is put forward to test the hardware functionality of embedded system.
论文所要设计与实现的测试平台就是为测试嵌入式系统硬件功能性而提出的。
The technical route of using fuzzy control for control of vibration cycle is put forward, and a fuzzy controller whose parameters can be optimized on line is designed.
提出了振动周期控制采用模糊控制的技术路线，设计了参数因子在线自整定的模糊控制器。
Using the PLC module made by Simons as a control core, S7-200 made by Simons is designed in remote gate control system, the draft of its composing and its system software program are put forward.
利用西门子公司的PLC模块作为控制核心，对西门子S7-200在远程闸门控制系统中的应用进行了设计。给出了闸门控制系统硬件构成和系统软件编程框图。
This system was applied to the city of NingBo, the thesis put forward the realization of system's truss as a whole and designed the soft ware of Data Service Center.
并把该项技术应用在宁波经济技术开发区路灯实验系统中，给出了系统总体构架的具体实现，设计了数据服务中心的软件部分。
Finally, the authors put forward the concrete project of digital scan conversion and designed the experimental system of this project.
最后，作者提出了数字式扫描转换技术的具体运用方案，设计了该方案的实验系统。
On the basis of analyzing vibratory frequency control system of vibratory roller, the controller are designed and the plan of vibratory frequency constant control by PID are put forward.
在分析振动压路机振动频率控制系统的基础上，对控制器进行了设计，提出了采用PID控制实现振动频率恒定的方案。
Based on actual project, duct system of evaporative condenser is designed and some advice is put forward to structure improvement.
同时结合工程实例对蒸发式冷凝器的管路进行了设计，并对其结构提出了改进意见。
Now a new plan is put forward that an optimal tension controller is designed by using tension state equation, and still further the tension comp.
现提出用张力状态方程设计张力最优控制器，进一步将张力最优控制器与预控速度的恒张力控制系统结合，设计热连轧张力复合控制系统的新方案。
We have designed some evaluation tables and put forward our views about the ways to carry on the process evaluation.
并就怎样进行形成性评价提出了我们的观点。
As for the combined signal, the sidelobe suppression method based on network synthesis is put forward and the irregular sidelobe suppression filter is designed.
针对混合调制信号，提出了一种基于网络综合的旁瓣抑制方法，设计了异型旁瓣抑制滤波器。
Special rolling tools are designed for machining special gland sealing gears in production and some schemes are put forward to be put into practice.
对生产中所遇到的特殊角度汽封齿的加工问题，设计了专用滚压刀具，并提出了实施方案。
Some key techniques were analyzed when designed vibration device, and a new method was put forward for small-diameter deep holes.
并分析了超声振动钻削装置设计中的一些关键技术问题，为在摇臂钻床上加工小直径深孔提供了一种新的工艺方法。
Based on laser propulsion thrust vector control, a thrice reflecting focus system is put forward, designed and fabricated.
基于激光推进推力矢量控制，提出、设计并加工了一种三次反射激光聚焦系统。
In this paper, a hydraulic pulling-winding system with load auto-adaptation is put forward. The structure and hydraulic control system are designed, and its winding performance is simulated.
本文提出了负载自动适应的减张力液压卷取系统的概念，对其结构及液压控制系统进行了设计，同时对系统的卷取性能进行了仿真。
A new lettering technology is put forward based on the electrochemical dissolving principle of anode, and the equipment for lettering is designed and lettering on bearing is tested.
利用电化学阳极溶解原理，提出一种新型脉冲电化学光亮刻字技术，设计了工装，并以轴承为例进行了刻字试验。
Quantitatively analyzing the effect of two to the profile of tooth, the inversing compensation method is then put forward to modify the die cavity and the electrode is designed.
在定量分析了两者对齿轮精度的综合影响之后，运用反补偿法预先修正齿形凹模，并进行了齿模电极的设计。
After the function is analyzed, the system control scheme is put forward. The control part was analyzed and realized. And the outline structure of the system is designed.
本文对功能进行分析后，提出了系统控制方案，分析并实现了控制部分，并且设计了系统的外形结构。
This paper gave a systematic analysis to the training process with performance technology and a solution plan was put forward, simultaneously an EPSS matched for the plan was designed.
运用绩效技术对培训过程进行了系统化分析并提出了解决方案，同时设计了一个配合解决方案的EPSS。
This paper brought forward the purpose and significance of the establishing designed and integrative experiment, put forward its thought, and introduced emphatically its contents and methods.
论述了开设设计性综合实验的目的和意义，提出了开设设计性综合实验的基本思路，重点介绍了综合实验的内容和实施方法。
The mechanical CAD graphics library was designed. The steps and interface were put forward.
设计了机构CAD图形库，并提出了该图形库生成步骤和人机交互界面。
The author put forward that we should construct object-oriented software reverse engineering database, and also designed and realized it.
提出应该构建面向对象的软件逆向工程数据库以支持软件逆向工程的特殊要求，并加以设计实现。
The paper analyses the structural characteristic and work principle of screw with variable pitch, designed machining technics, put forward a particular method of nc programming.
文中分析了异型截面供送变螺距螺杆的结构特点和工作原理，设计了其加工工艺，提出了一套加工该螺杆的独特的数控编程方法。
Based on in depth studies of structure of membranes, the principle of water osmosis in single direction was put forward, and water osmotic plastic film was designed and developed.
经过对地膜物料结构的深入研究，提出了单向渗水原理，设计并发明了渗水地膜。
Based on in depth studies of structure of membranes, the principle of water osmosis in single direction was put forward, and water osmotic plastic film was designed and developed.
经过对地膜物料结构的深入研究，提出了单向渗水原理，设计并发明了渗水地膜。
应用推荐