Ports are numbered from 0 to 65535 and only one application at a time may register for a single port.
端口的数字可以从0到65535并且一个程序每次只能有一个端口。
If this variable is not set, it will default to the partition that is defined with port 0 on the machine (in the db2nodes.cfg file).
如果没有设置该变量，那么它将默认地等于用机器上的端口0定义的那个分区(在db 2 nodes . cfg文件中)。
Enter interface managementethernet 0 — Configures the management port from the configure prompt.
输入interface managementethernet0——在配置提示符上配置管理端口。
The STA adapter is always bound to Port 0.
STA网卡只能被绑定到端口 0。
Click on the Remote TAB, and this time accept the defaults (localhost on Port 0).
单击Remote选项卡，这次接受默认值(端口0上的localhost)。
Note: if you set the source port to 0, your operating system will specify the source port.
注意：如果你的端口被设置为0，你的操作系统将被指定为源端口。
Use the label "serial 1/0", when the interface is serial, the slot number where the module is installed is slot 1, and the port that is being referenced is port 0.
当界面是序列的时候使用标签”序列1/0“，位置数字组件被安装的地方是位置1，并且参考的港口是港口0。
If you are not sure about whether a port is available, use 0 (zero) when configuring your channel's port and the remoting system will choose an available port for you.
如果你不确定是否一个端口可用，使用0(零)当配置通道的端口和远程系统将为你选择一个可用的端口。
To use concurrent transactions within a single VM, we just open a db4o server on our database file, directing it to run on port 0, thereby declaring that no networking will take place.
要在单个VM上执行并行事务，只需要在数据库文件上打开一个服务器，指定其运行端口为0，这样声明就不会有网络的发生。
A city of central Italy on the Adriatic Sea. It is a leading port and an industrial and commercial center. Population, 0 ', 42.
意大利中部一城市，邻亚得里亚海。是重要的港口和工商业中心。人口0'，42。
Port Numbers must be greater than 0 and less than 65536. Please enter a number within this range.
端口数目必须大于0小于65536。请键入一个在这个范围内的数目。
DMA can run constantly or can be triggered by exterior interruption (INT3-0), interior interruption (timer and serial port), at the end of transfers, send interruption signal to CPU.
DMA可以被外部(INT3 - 0)、内部的(片内定时器和串口)中断触发运行，传输完成后可以向CPU发出中断请求。
Port 0 is also the multiplexed low-order address and data bus during access to external program and data memory.
端口0也是复低位地址和在利用外部程序和数据存储器的数据总线。
This approach can work because in some systems "0" is invalid ports, When you attempt to use a normally closed the port connecting to it will produce different results.
这一方法能够工作是因为在一些系统中“0”是无效端口，当你试图使用一种通常的闭合端口连接它时将产生不同的结果。
For the five-port waveguide junction properly to be used in a six-port reflectometer, needing the reflection coefficient looking into anyone port is less than 0.
为了使五端口波导网络能较好地工作于六端口反射计中，要求各端口反射系数的绝对值小于0。
When you sample an analog port it will return a value between 0 and 1023, proportional on the voltage (05 volts) on the signal pin (pin 3).
当你对一个模拟端口采样时，它会返回一个与信号针脚（脚3）上的电压成比例的，范围在0至1023之间的值。
Send Port referenced by Orchestration Port '{0}' has been deleted.
业务流程端口“{0}”引用的发送端口已被删除。
A port of 0 creates a socket on any free port.
端口号为0表示在任意空闲端口创建套接字。
SendPortGroup referenced by Orchestration Port '{0}' has been deleted.
业务流程端口“{0}”引用的发送端口组已被删除。
Normal working hours at Discharging Port shall mean from 0 (zero) to 24 (twenty-four) o 'clock, including Saturdays, Sundays and holidays.
在卸港的正常工作时间意即零时(0)至二十四时(24)，包括周六、周日和节假日。
Normal working hours at Discharging Port shall mean from 0 (zero) to 24 (twenty-four) o 'clock, including Saturdays, Sundays and holidays.
在卸港的正常工作时间意即零时(0)至二十四时(24)，包括周六、周日和节假日。
应用推荐