The liquid is maintained above its melting point until steam is required, at which point the liquid is allowed to turn back into a solid, releasing its stored energy.
不需要蒸汽时，液体保持在熔点以上，需要蒸汽时液体才能变成固体，释放其储存的能量。
The liquid is maintained above its melting point until steam is required at which point the liquid is allowed to turn back into a solid releasing its stored energy.
液体保持在其熔点以上，直到需要蒸汽时才可以变回固体，释放其储存的能量。
No matter how you slice it, a greasy slick will ooze out of melting cheese, when heat renders liquid fats that were solid at room temperature.
不管你怎么切，融化的奶酪都会渗出油腻粘滑的油脂，因为室温下呈固态的脂肪一旦受热就会变成液态。
Any type of solid or semi solid organic material of natural or synthetic origin, generally of high molecular weight with no defined melting point. Most resins are polymers.
一类固体或半固体的天然的或合成的有机材料，一般为无清晰熔点的高分子量材料，多数树脂为聚合物。
Solid-metal embrittlement by cadmium can occur at temperatures below the cadmium melting point.
低于镉的融解点温度时会出现故态金属的镉脆化。
When the reaction products form as high melting point CA2, CA6 and MA spinel in a continuous solid phase it will clog the liquid channel and resist the further diffusion of fused slag in the brick.
并且当熔渣与耐火材料的反应产物为高熔点的CA2、CA6和MA尖晶石相且连续交错分布时，能堵塞液相扩散通道，抑制熔渣向耐火材料内部的进一步渗透。
The complexity of solid sulfur's melting process and so many factors affecting the heat transfer area make the calculation of sulfur's melting process quite complicated.
固体硫磺的熔融过程较为复杂，影响传热面积的因数很多，熔硫槽传热面积的计算颇为繁琐。
The quality of solid greases depends on the Crystal polymorphism it is very important to determine the melting point of Crystal polymorphism and it's stable CharaCter.
固体油脂食品的品质优劣取决于同质多晶晶型，所以确定各晶型的熔点及其稳定性是十分重要的。
In this paper, driving power consumption of the solid conveying and melting process in conical twin-screw extruder was studied.
本文旨在对锥形双螺杆挤出机挤出过程中固体输送和熔融两段的物料输送功率进行研究。
The effects of natural convection and moving of solid PCM on melting heat transfer are compared.
固态相变材料的运动对熔化传热过程有着重要影响。
Combined with the experimental results, the equation is put forward for calculating the melting length of the broken solid pieces.
根据固相加速实验结果，提出固相碎块轴向熔融长度计算公式。
Combined with the former experiment for solid conveying zone and melting zone, the torque for extruding zone was obtained.
结合课题组过去所做的固体输送段和熔融段两段的实验，得出了各实验条件下螺杆挤出段的扭矩。
Under normal condition, effect on element of solid melting Cu is big and on element separated out of the second phase is small.
正常状态下，对固态熔铜的影响很大，而对分离的第二相则比较小。
It has low melting point and good wettability to the base-metal, and contains a high-strength and high-hardness solid solution structure, with a high strength of soldering joint.
该钎料具有熔点低，对母材的润湿性好，钎焊接头组织中含有强度、硬度较高的呈弥散分布的固溶体，以及接头强度较高等特点。
For smaller clusters, there is no clear characteristic of first-order phase transition during the melting, implying a coexistence of solid and liquid phases due to finite-size effect.
对于较小的团簇，融化曲线没有出现清楚的一级相变特征，意味着由于尺寸效应导致的固态液态共存。
Method: carvedilol solid dispersions were prepared by solvent-melting and coevaporation methods with PEG-6000 and PVP as carriers, the study on the dissolution was conducted in vitro.
方法：以聚乙烯吡咯烷酮（PVP）、聚乙二醇-6000（PEG-6000）为载体，溶剂法和溶剂熔融法制备固体分散体，并进行体外溶出度研究。
METHODS Preparing the solid dispersion by melting method at different drug-to-PEG ratios with different PEG moleculars and studying the preparation with dissolution rate in vitro and DSC method.
方法以不同分子量不同比例的聚乙二醇为载体，以熔融法制备固体分散体，并进行体外溶出度研究和DSC扫描。
Fenofibrate solid dispersion tablets were prepared by solvent melting method using PEG4000 and sodium lauryl sulfate.
PEG4000十烷硫酸钠体，溶剂-熔融制备非诺贝特固体散体，再适辅混合压片制非诺贝特固体散片。
Put a lot of this kind particles together will soon to form a solid solder, which need the temperature rise to the melting point for remelting.
所以如果二次回焊的温度过高，还是可能造成第一面的焊点重新熔融，零件可能掉落的风险。
A new way for making industrial pure iron is put forward. It includes three steps-hot metal granulation, solid state decarbonization and electric furnace melting down.
本文提出一种铁水粒化-固态脱碳-电炉重熔制备工业纯铁的新工艺。
The ceramics matrix composites can be formed by pseudo-semi-solid thixoforming and the forming temperature was much lower than the melting temperature of the high-melting phase-nano-powder.
用伪半固态触变成形技术能够成形陶瓷基复合材料，成形温度大大低于高熔点相纳米粉体熔化温度。
The conveying cause of natural food material cannot develop into solid-bed and melting-poor condition.
高分子物料在挤出加工过程中，难以形成明显的固体床和熔池。
The conveying cause of natural food material cannot develop into solid-bed and melting-poor condition.
高分子物料在挤出加工过程中，难以形成明显的固体床和熔池。
应用推荐