The peak cobalt rodlet temperature doesn't exceed the cobalt melt temperature during these two cases.
在这两种情况下，钴小棒的峰值温度不会超过钴的熔化温度。
Flow in the melt temperature uniform.
流道中熔体温度均匀。
Expect the melt temperature to rise somewhat.
希望把熔体温度升高一些。
With the increase of the melt temperature, the evaporation trend increases.
随着熔体温度的增加，挥发趋势也增大。
The melt temperature decreases linearly with the increase of the charge mass.
炉料质量与熔体温度呈线性关系，随着炉料质量的增大熔体温度降低。
Start by determining the true melt temperature and set the die body to that temperature.
从确定真正的熔体温度开始，然后按照这个温度设定口模体的温度。
Surface Imperfections: Melt temperature may be too high causing resin decomposition and gas evolution (bubbles).
外观不完整：塑料熔化温度过高导致树脂分解和气泡。
Our results show that mechanical properties of PP samples strongly depend on the melt temperature and mold te...
实验结果表明，熔体温度和模具温度对试样的力学性能有重要影响。
The effects of pressure and frequency on ABS samples of different melt temperature under vibration field were studied.
研究了在振动场作用下，ABS试样在不同的温度熔体下受振动压力和频率的影响。
Our results show that mechanical properties of PP samples strongly depend on the melt temperature and mold temperature.
实验结果表明，熔体温度和模具温度对试样的力学性能有重要影响。
The melt temperature, stirring speed and proper shearing time were beneficial to the formation of fine globular grains.
即降低降体温度、搅拌速度及适当剪切时间有利于细小球形晶粒的形成。
The mold temperature obviously influences the molding process, while the melt temperature influences comparatively less.
模具温度对成型过程的影响较大，熔体温度的影响相对较小。
Unmelted gels have the same melting point as the surrounding resin, but remained colder than the average melt temperature.
不熔凝胶与周围树脂有同样的熔点，但是受热温度比平均温度低。
The melt flow index of the blends was increased when the content of PEEK was decreased and melt temperature was increased.
结果表明：共混物的熔体流动指数随PEEK含量的降低和熔体温度的升高而增加；
After put into running, the melt temperature is steady, the running of the regulating valve is smooth, the effect is good.
投入运行后，熔体温度稳定，调节阀动作平稳，效果良好。
The results show that the peak cobalt rodlet temperature doesn't exceed the cobalt melt temperature during these two cases.
结果表明，两种情况下钴靶元件最高温度均未超过其熔点。
The constant volumetric delivery and melt temperature reduction bring a significant improvement in the quality of the end product.
稳定的体积流量和降低熔体温度对于改善最终产品的质量有重要意义。
The two kinds of viscosities were significantly affected by the rate of shear, melt temperature and 2, 7-naphthalenediol unit content.
而剪切速度、熔体温度及2,7 -萘二酚链节含量对此两种粘度有重大的影响。
Process window analysis, another part of mold flow analysis, examines melt temperature, mold temperature, injection pressure, and fill times.
加工窗口分析、它零件的模流分析，检查熔体温度、具温度、塑压力和充填时间。
On the contrary, when melt temperature is too low, the melt viscidity becomes intensive, so cavitation and acoustic streaming are in no effect.
如果施振温度过低，熔融合金粘度就会增大，致使声空化和声流效应发挥不了应有的作用。
The static and dynamic mechanical properties have been studied for PP that have been injected at different melt temperature and mold temperature.
本文研究了在不同的熔体温度和模具温度下，注射成型的聚丙烯塑料试样的静态和动态力学性能；
The effects of the moisture content in polyester chip, the melt temperature and pressure, and the shear rate on the shear viscosity are discussed.
探讨了聚酯切片含水率、熔体温度、熔体压力、切变速率对熔体切变粘度的影响。
The molder must recognize the dangers of excessive fill speed, insufficient injection pressure, excessive melt temperature, and inadequate packing.
注塑工必须认识过快填充速度、不足注塑压力、过高融化温度和不充分挤压的危害性。
The effects of compact load, surface area and thickness of the pellets and the melt temperature on reaction of electro-deoxidation were investigated.
研究了试样的成型压力、烧结程度、表面积，以及熔盐温度和阳极碳棒直径大小等对电脱氧反应速度及脱氧产物氧含量的影响。
The addition of PHE also reduced the melt temperature of blends, which result from the dilution effect of PHE that reduced the degree of PA66 crystal.
由于PHE的加入起到稀释效应或是使得PA66晶体的完善程度降低，从而使得共混物的熔点降低。
That means there is no feedback from any other measurement that would alter the melt temperature, nor is melt temperature used to control anything else.
这就意味着没有什么测量反馈来改变熔体温度，熔体温度也不用于控制别的什么东西。
The interface motion situation of gas-melt is changed when injecting gas into melt in various conditions-gas-entering pressure, melt temperature and so on.
气体经喷嘴进入聚合物熔体时所形成的气熔界面的运动情况随着进气压力、熔体温度等不同参数的改变而发生变化。
The results show that the apparent density of hard elastic polypropylene increases with a lower melt temperature, or a higher draft ratio, or a higher air blasting speed.
结果表明，熔体温度下降、所受拉伸比增加或冷却风速度升高均可使表观密度增加。
The factors that affect thin-wall mould warpage, such as mould temperature, melt temperature, rate of injection and holding pressure, etc, are analyzed, in addition the ca…
对影响薄壳塑件翘曲变形的因素（如模具温度、熔体温度、注射速率、保压压力等）进行分析，提出翘曲产生的原因及相应的改进措施。
The factors that affect thin-wall mould warpage, such as mould temperature, melt temperature, rate of injection and holding pressure, etc, are analyzed, in addition the ca…
对影响薄壳塑件翘曲变形的因素（如模具温度、熔体温度、注射速率、保压压力等）进行分析，提出翘曲产生的原因及相应的改进措施。
应用推荐