The peak cobalt rodlet temperature doesn't exceed the cobalt melt temperature during these two cases.
在这两种情况下，钴小棒的峰值温度不会超过钴的熔化温度。
With the increase of the melt temperature, the evaporation trend increases.
随着熔体温度的增加，挥发趋势也增大。
Our results show that mechanical properties of PP samples strongly depend on the melt temperature and mold te...
实验结果表明，熔体温度和模具温度对试样的力学性能有重要影响。
Our results show that mechanical properties of PP samples strongly depend on the melt temperature and mold temperature.
实验结果表明，熔体温度和模具温度对试样的力学性能有重要影响。
The mold temperature obviously influences the molding process, while the melt temperature influences comparatively less.
模具温度对成型过程的影响较大，熔体温度的影响相对较小。
The melt flow index of the blends was increased when the content of PEEK was decreased and melt temperature was increased.
结果表明：共混物的熔体流动指数随PEEK含量的降低和熔体温度的升高而增加；
After put into running, the melt temperature is steady, the running of the regulating valve is smooth, the effect is good.
投入运行后，熔体温度稳定，调节阀动作平稳，效果良好。
The results show that the peak cobalt rodlet temperature doesn't exceed the cobalt melt temperature during these two cases.
结果表明，两种情况下钴靶元件最高温度均未超过其熔点。
The two kinds of viscosities were significantly affected by the rate of shear, melt temperature and 2, 7-naphthalenediol unit content.
而剪切速度、熔体温度及2,7 -萘二酚链节含量对此两种粘度有重大的影响。
The effects of the moisture content in polyester chip, the melt temperature and pressure, and the shear rate on the shear viscosity are discussed.
探讨了聚酯切片含水率、熔体温度、熔体压力、切变速率对熔体切变粘度的影响。
That means there is no feedback from any other measurement that would alter the melt temperature, nor is melt temperature used to control anything else.
这就意味着没有什么测量反馈来改变熔体温度，熔体温度也不用于控制别的什么东西。
The interface motion situation of gas-melt is changed when injecting gas into melt in various conditions-gas-entering pressure, melt temperature and so on.
气体经喷嘴进入聚合物熔体时所形成的气熔界面的运动情况随着进气压力、熔体温度等不同参数的改变而发生变化。
The results show that the apparent density of hard elastic polypropylene increases with a lower melt temperature, or a higher draft ratio, or a higher air blasting speed.
结果表明，熔体温度下降、所受拉伸比增加或冷却风速度升高均可使表观密度增加。
On the other hand, by improving the control of the melt temperature, it can distinctly reduce the waste of energy, pull the cost down and enhance the efficiency of extrusion.
另一方面，通过加强对物料的温度控制，可以减少能量的浪费，降低生产成本，提高挤出效率。
The influence of the melt temperature on the crystalline morphology of polytetrafluoroethylene was studied by Small Angle Light Scattering and Electron Microscope techniques.
用小角光散射、电子显微镜等方法研究了熔体温度对熔融结晶的PTFE结晶形态的影响。
The influences of processing parameters, material properties and screw design on melt temperature distribution in reservior during injection moulding are described in this paper.
本文叙述了注射成型中加工参数、物料性能及螺杆结构对存料区熔体温度分布的影响。
Surface Imperfections: Melt temperature may be too high causing resin decomposition and gas evolution (bubbles).
外观不完整：塑料熔化温度过高导致树脂分解和气泡。
Surface Imperfections: Melt temperature may be too high causing resin decomposition and gas evolution (bubbles).
外观不完整：塑料熔化温度过高导致树脂分解和气泡。
应用推荐