The measuring error is analyzed.
重点对误差进行分析。
The measuring error of the whole system is analysed.
最后还进行了整个系统测量误差的分析。
Temperature error is the main factor that produces the measuring error.
温度误差是产生测量误差的主要因素。
Various causes of measuring error are analysed and the resolving method is presented.
深入研究了各种可能引起测量误差的原因，并提出了解决办法。
To decrease the measuring error, the balance bridge is often used in the bridge measurement.
电桥测量中，为了减少测量误差常常采用平衡电桥。
The results are consonant with the data reported by references, and the measuring error is about 5%.
结果与文献报道数据吻合，测量误差约为5%。
Then apply the formula to the fields of the CMM measuring error modeling, and get the better results.
将该公式应用于三坐标测量机误差建模领域，取得了较好的建模效果。
On the basis of above research, the measuring error compensation method for free-form surface is proposed.
在此基础上，进一步提出了自由曲面测量误差的补偿方法。
Through the analysis of the experiment results, the methods of reducing measuring error of the system are provided.
通过对实验结果的分析，提出了减小系统测量误差的方法和措施。
The measured parameters of the waveguide agreed with data measured by using guided mode method in measuring error ranges.
测得的波导参数在测量误差范围内与用导模法测得的数据一致。
The statistical results in experiments show that the registration error of this method is about 66% of the system measuring error.
实验统计结果表明，该方法的配准误差约为系统测量误差的66%。
In error minimum design of the navigation precision, geometrical error, measuring error and calculating error are considered well.
本设计从几何误差、测量误差和计算误差几个方面对导航精度进行了误差最小化设计。
A method for compensating the measuring error of the grating displacement measurement system with absolute zero mark is presented.
提出一种具有绝对零位标识的光栅位移测量系统的误差补偿方法。
The kinematical equation of the probe and the equation of measuring error caused by the swaying of the measuring arm are established.
建立了测头的测量运动方程和关节晃动引起的测量误差的方程。
This paper introduces a testing method of dynamic measuring error of angles for infrared system of photoelectric measuring equipment.
介绍了一种光电测量设备红外测量系统动态测角误差检测方法。
Because the voltage measuring error increases when phase to phase short circuit occurs, distance relay protection will act improperly.
但是短线路在两相短路时，由于测量电压的误差会放大，可能引起距离保护的超越。
The reason of the measuring error in tool setting gauge for machining center and the method to reduce the measuring error were analyzed.
分析了加工中心对刀仪器测量误差产生的原因和减少测量误差的措施。
This paper also analyses how to realize distribution of angle measuring error when we are given to the certain error of angle measurement.
论文还分析了在给定测角误差情况下，如何实现测角误差分配。
Based on this, the formulas for calculating, according to the minimum condition, the measuring error limits of straightness have been derived.
在这基础上，推导出了按最小条件评定直线度的极限测量误差的计算式。
This paper introduces the measurement of the parallelisms for line and flat to space turning spindle axis. The measuring error is analysed also.
本文介绍一种线、面对空间回转轴线平行度的测量方法，并进行了误差分析。
For vibratory gyro, very small coupling error will induce great measuring error because driving vibration is much greater than sensing vibration.
由于驱动振动幅度远大于读出振动，因此极小的耦合量就会造成很大的检测误差。
The phase detection and curve-fitting techniques have been used in processing the interferogram, and sub-pixel measuring error has been obtained.
在干涉图的处理中，采用了相位检测和曲线拟合技术，得到了亚象素的测量精度。
In order to reduce the measuring error of automatic detection systems, it is needed to adjust the nonlinear error for automatic detection systems.
为减少检测系统的测量误差，在自动检测系统中需要对非线性误差进行校正。
It is illustrated how to reasonably select measurement reference for complex parts in order to improve measuring accuracy and lower measuring error.
阐述了一些复杂零件如何合理选择测量基准，以提高零件的测量精度，减小检测误差。
The relation between the measuring error of standard addition method for ion selective electrode and the added amount of the standard solution was studied.
研究了离子选择性电极标准加入法的测量误差与标准溶液加入量的关系。
In flying height measuring method utilizing light intensity interference principle, the position control of micro flying head has effect on measuring error.
基于强度干涉原理的飞高检测方案中，微型飞行头位姿控制是影响测量误差的一项关键因素。
Most scholars were committed to study the low-dimensional measuring error of the CMM(Coordinate Measuring Machine), few to research the high-dimensional model.
目前对三坐标测量机测量误差建模的研究，常见的是低维模型，多元模型很少有学者探讨。
As far as big diameter pipe gas transport is concerned, gas flow distribution will influence the flow measurement performance, and cause a large measuring error.
对于大管径气体传输来说，气体流场分布情况会影响流量测量的性能，并造成较大的测量误差。
Under conditions of monochromatic light and a small object, the spherical aberration was the main factor which led to measuring error of focus of thin convex lens.
在单色光、小物条件下，球差是引起薄凸透镜焦距的测量误差的主要因素。
In this paper, the signal quality is improved via denoising in wavelet transformation domain, as a result the measuring error of stabilization precision is reduced.
本文利用小波变换对火炮误差角信号进行处理，改善了误差角信号的质量，有效减小了稳定精度的测量误差。
应用推荐