The measuring error is analyzed.
重点对误差进行分析。
The measuring error of the whole system is analysed.
最后还进行了整个系统测量误差的分析。
The experiment demonstrates that measuring error is less than 0 92%.
实验结果表明，其测量电压误差不大于0 92 %。
Using experiment data, we analyze the measuring error of two methods.
通过实验数据，分析了两种算法的误差。
The influence of thermal deformation on measuring error is considered.
对测量装置结构进行优化设计，减小热形变的影响；
Temperature error is the main factor that produces the measuring error.
温度误差是产生测量误差的主要因素。
False negative. Measuring error results in acceptance of defective sample.
错误的坏的方面。误测导致验收不符合标准的样品。
Various causes of measuring error are analysed and the resolving method is presented.
深入研究了各种可能引起测量误差的原因，并提出了解决办法。
The measuring error of vortex street flowmeter was investigated in condition of mist flow.
研究雾状流条件下，离散液相对涡街流量计测量误差的影响。
To decrease the measuring error, the balance bridge is often used in the bridge measurement.
电桥测量中，为了减少测量误差常常采用平衡电桥。
The analysis method of the fuel measuring error caused by the aircraft attitude is presented.
提出并实现了油量姿态误差的分析方法。
The results are consonant with the data reported by references, and the measuring error is about 5%.
结果与文献报道数据吻合，测量误差约为5%。
On the basis of above research, the measuring error compensation method for free-form surface is proposed.
在此基础上，进一步提出了自由曲面测量误差的补偿方法。
By doing so, there will only be standard frequency error in theory and decrease the measuring error greatly.
这样使测频误差在理论上只含有标准频率误差，可以使测量误差降低。
Through the analysis of the experiment results, the methods of reducing measuring error of the system are provided.
通过对实验结果的分析，提出了减小系统测量误差的方法和措施。
The measured parameters of the waveguide agreed with data measured by using guided mode method in measuring error ranges.
测得的波导参数在测量误差范围内与用导模法测得的数据一致。
Then the modeling method is applied on the tuning of temperature measuring error during the processes of oil pipes are heated.
采用这一建模方法对石油钻杆在热处理过程中的温度测量偏差进行校正。
The statistical results in experiments show that the registration error of this method is about 66% of the system measuring error.
实验统计结果表明，该方法的配准误差约为系统测量误差的66%。
The kinematical equation of the probe and the equation of measuring error caused by the swaying of the measuring arm are established.
建立了测头的测量运动方程和关节晃动引起的测量误差的方程。
This paper introduces a testing method of dynamic measuring error of angles for infrared system of photoelectric measuring equipment.
介绍了一种光电测量设备红外测量系统动态测角误差检测方法。
The main problem in radiation thermometry is how to minimize the measuring error resulting from unknown or variant surface emissivity.
辐射测温的主要问题是解决未知的或变化的表面发射率所引起的误差测量。
Because the voltage measuring error increases when phase to phase short circuit occurs, distance relay protection will act improperly.
但是短线路在两相短路时，由于测量电压的误差会放大，可能引起距离保护的超越。
The reason of the measuring error in tool setting gauge for machining center and the method to reduce the measuring error were analyzed.
分析了加工中心对刀仪器测量误差产生的原因和减少测量误差的措施。
Error analysis shows that the displacement measuring error entirely depends on geometric positioning precision of the first bar code center.
误差分析表明：位移测量误差完全取决于首条码中心几何定位。
Based on this, the formulas for calculating, according to the minimum condition, the measuring error limits of straightness have been derived.
在这基础上，推导出了按最小条件评定直线度的极限测量误差的计算式。
This paper introduces the measurement of the parallelisms for line and flat to space turning spindle axis. The measuring error is analysed also.
本文介绍一种线、面对空间回转轴线平行度的测量方法，并进行了误差分析。
For vibratory gyro, very small coupling error will induce great measuring error because driving vibration is much greater than sensing vibration.
由于驱动振动幅度远大于读出振动，因此极小的耦合量就会造成很大的检测误差。
The phase detection and curve-fitting techniques have been used in processing the interferogram, and sub-pixel measuring error has been obtained.
在干涉图的处理中，采用了相位检测和曲线拟合技术，得到了亚象素的测量精度。
In order to reduce the measuring error of automatic detection systems, it is needed to adjust the nonlinear error for automatic detection systems.
为减少检测系统的测量误差，在自动检测系统中需要对非线性误差进行校正。
It is illustrated how to reasonably select measurement reference for complex parts in order to improve measuring accuracy and lower measuring error.
阐述了一些复杂零件如何合理选择测量基准，以提高零件的测量精度，减小检测误差。
应用推荐