A discussion of optimal contact force distribution is also included.
并对抓持力的分配进行初步讨论。
Permanent set is one method by which the contact force decreases over time.
永久变形是触点压力随着时间变化而降低的一种方式。
A novel apparatus is developed for automatic dimple contact force measurement.
实现了一种用于自动测量弹性臂窝点接触力的新型测试仪。
Stress relaxation is another phenomenon that results in loss of contact force.
应力松弛是导致触点压力损失的另一现象。
Since the stress is what generates the contact force, the force will decrease as well.
因为应力产生触点压力，所以触点压力也会降低。
Side and bottom contact shoes are spring loaded to provide the necessary contact force.
边触式和下触式集电靴装有弹簧用来提供所需的接触压力。
The author used the contact theory to found the gap element, and used it to solve the contact force.
利用现有的接触理论和计算方法，在模型的接触处构造了间隙单元来求解接触压力。
The contact force during impact process was measured by force sensor and data signal processing system in real time.
冲击过程中的接触载荷由压力传感器及数字信号处理系统实时测量。
Finally, the distributing and evolving features of contact force network in dense granular systems are investigated.
最后，分析了密集颗粒系统内接触力网的分布及演化特征。
The contact method with low contact force on Al electrodes is required for test probing of LSI for the next generation.
下一代的大规模集成电路的测试探头要求使用在铝电极上的低接触力的联接方法。
Driving wheels, guiding wheels, track rack will have contact force with crawler boards while the walking device running.
在运行时行走装置的驱动轮、导向轮、履带架与履带板都会产生接触力作用。
The relationships between dynamic contact force and indentation are derived in the case of longitudinal wave propagation.
在仅考虑纵波传播的情况下，寻出了撞击力-压入位移关系。
The dynamic contact force method is a relatively accurate method for solving dynamic contact problems in viscoelastic media.
动接触力算法是求解粘弹性动接触问题的精度较高的方法之一。
If we look at technologies that are becoming available, certainly something that is very important are contact force sensors.
如果我们观察这些可利用的技术，在其中可以肯定的是接触压力传感器是非常重要的。
The hypotheses are categorized into two groups: the contact force entrainment hypothesis and the non-contact force hypothesis.
进一步将风沙起动假说归纳为以接触力为主的起动学说和以非接触力(气力)为主的起动说两大类。
And that contact force better be exactly the same as mg, but in opposite direction, otherwise there could never be equilibrium.
触点压力和，mg完全，相同，但是反向相反，否则永远都不会有平衡。
We also set up an impedance model of the environment during the contact, and propose the calculating method of virtual contact force.
建立了环境在稳定接触过程中的阻抗模型，提出了虚拟力的计算方法。
This means that any subsequent deflection of the contact will be smaller, and the corresponding contact force will be reduced as well.
这意味着该触点任何后续的变形都将会很小，且相应的触点压力也会降低。
When the force can not contact drill string with one side of the borehole wall, the stiffness of drill string can influence the contact force.
当外力不足以使钻柱紧贴于井壁的一侧时，钻柱的刚度对钻柱与井壁之间的接触力有影响。
The catenary's shape influenced by gravity is curve, and the pantograph-catenary contact force changes regularly with pattern during one span.
在重力作用下的接触网是悬链形，弓网接触力在一个跨距内呈现规律的起伏变化。
Based on the achieved contact force data, the relation of the contact force and deformation depth of specimens can be obtained by calculation.
根据接触载荷数据，可计算得到接触载荷与样品表面变形的关系。
Coupled with circuit equations, the opening time of movable contact also can be calculated using iteration with the restriction of contact force.
通过耦合电路方程，并以动触头上的预压力为约束，经迭代运算，确定动触头的打开时间。
The method can calculate the contact force and its change range between the pin gear and the cycloid during the whole transmission more precisely.
该方法可以比较精确地计算在整个传递过程中针齿和摆线轮齿面接触力的大小和变化范围。
In the thesis, the contact stress, bending stress on the root and the contact force on the tooth have been calculated by Finite Element Method (FEM).
文章采用有限元接触计算方法，计算了螺旋锥齿面接触应力和齿根弯曲应力以及齿面接触合力。
Making use of communication based on can force sensor can send contact force information to robot controller for force control immediately and accurately.
采用CAN通讯可以确保力传感器准确、及时地把力信息传送给控制器进行力控制。
The tangency point of Bottom Hole Assembly is located at where the drill string just touches the wall of the borehole, and the contact force is zero here.
在计算底部钻具组合的受力和变形时，以前一般都是按弯矩为零的条件来确定其上切点的位置。
The tangency point of Bottom Hole Assembly is located at where the drill string just touches the wall of the borehole, and the contact force is zero here.
在计算底部钻具组合的受力和变形时，以前一般都是按弯矩为零的条件来确定其上切点的位置。
应用推荐