The co concentration reduces with increase in the bed temperature.
CO排放浓度随床温升高而降低。
The effect of bed temperature and pressure on PSD can be neglected.
同时发现，床层压力和温度对聚乙烯粒径分布的影响很小。
The drying rate increases with increasing bed temperature and decreasing product size.
干燥速率随流化床温度的提高和物料尺寸的减小而加快；
The process of dynamic modeling for bed temperature system of CFB boiler is displayed.
根据所提的建模方法对某电厂已投产的一台循环流化床锅炉实际建模。
With the rise of bed temperature, the desulfurization efficiency is linearly increased.
随着炉床温度的上升，脱硫效率线性下降。
Adding limestone to coal during would cause a slight fluctuation in the boiler's bed temperature.
加入石灰石脱硫会引起炉床温度波动，但波动幅度不大。
The wax models with high accuracy were sintered by filtering powder bed temperature of sintering process.
通过对烧结过程中粉床温度的筛选，烧结出尺寸精度较高的蜡模。
The bed temperature measurement is crucial for CFB boiler as a result of desulphurization and denitration.
床温测量对于循环流化床(CFB)锅炉至关重要，直接影响炉内脱硫和脱硝。
Combustion efficiency also decrease with bed temperature because of the decrease in strength of the fuel agglomerates.
由于煤泥凝聚团的强度随沸腾床温度的降低，沸沸炉的燃烧效率也随床温降低而有较明显的降低。
So the low control level of the bed temperature, as an important parameter of circulating fluidized bed boiler, is keeping.
因此，作为循环流化床锅炉燃烧控制系统中的一个重要参数的床温的自动化控制水平一直无法得到有效提高。
The control of catalyst bed temperature in a fixed bed reactor during high exothermic reactions is of primary concern to designers.
在强放热反应的固定床催化反应器的设计中，床层温度的控制常成为设计的主要焦点。
The higher the bed temperature, longer the resident time, and stronger the vibration, the more intensive the fragmentation process is.
较高的温度、较长的停留时间、较大的振动强度可以强化碎裂。
The absorption process is a spontaneous endothermic reaction. Accordingly, adequate drop of bed temperature is helpful for the absorption.
吸附过程是自发进行的吸热反应，适当降低床层温度有利于吸附过程。
The effects of bed temperature, input concentration, apparent gas speed, and absorbent grain size on the absorption performance were studied.
考查了床层温度、进料浓度、表观气速和吸附剂粒径对吸附性能的影响。
Powder bed temperature of sintering process should be lower than agglomeration temperature of composite wax powder, which result in dimensional instability.
为了使蜡模获得稳定的尺寸，烧结过程中的粉床温度应尽量低于蜡粉材料的板结温度。
The main steam pressure control system, bed temperature measure system, bed temperature adjust system and action condition of main fuel trip (MFT) are analyzed.
对主蒸汽压力控制系统、床温测量系统、床温校正系统和主燃料跳闸的动作条件进行了详细的分析。
In this thesis, through the analysis on mass balance and energy balance in the dense phase and sparse phase, the bed temperature cybernetic model is established in this thesis.
本文通过对循环流化床锅炉密相区和稀相区的质量平衡与能量平衡的分析，建立了床温控制模型。
In order to build the DPF pressure drop model based on air intake flow, DPF bed temperature, soot and fuel charge, the paper has carried out a series of tests, collected a mass of data.
为了建立基于进气流量、DPF床温、碳烟以及喷油量的DPF压降模型，论文进行了一系列的试验，采集了大量数据。
The effects of the feed rate of air, steam and coal on bed temperature, gas composition, calorific value, carbon conversion and gasification efficiency are predicted and analyzed with the model.
在此基础上，还就空气加入量、蒸汽加入量及加煤速率对床温、煤气组成、煤气热值、碳转化率和气化效率的影响做了预测和分析。
The results show that the temperature of the smaller char particle is close to the bed temperature, and there also exists a peak value for the burn-out time of char particles versus their diameters.
结果表明：粒径越小，其温度越接近于床内环境温度，而且燃尽时间随粒径变化的曲线将出现峰值。
The nurse checked Keith's vitals and temperature and wrote them down on a chart by the bed.
护士检查基斯的脉搏，并为他测试了体温，然后把检查数据写在床边的图表上。
Using a digital thermometer or a thermometer specifically designed to measure basal body temperature, take your temperature every morning before you get out of bed.
运用数字体温计或基础体温专用体温计在每天早晨起床前进行测量。
Another type of high temperature gas reactor is what we call a pebble bed reactor.
另一种高温的气体反应堆是，我们称之为卵石层反应堆。
'Try a bath before you go to bed - this helps to raise the body temperature and, as it decreases, you should feel ready to nod off,' says Victoria Dawson.
“你可以试着在睡前洗个澡——这会帮助升高体温，之后当体温降低时你就会觉得瞌睡了。”维多利亚·道森说。
Now the pebble bed reactor has the same basic safety features as a high temperature prismatic reactor in a sense that it has a meltdown free core.
现在，卵石层反应堆有相同的基本，安全特征和高温棱柱反应堆一样，因为它有一个熔化的核心。
If you eat too soon before going to bed your metabolic rate and body temperature will increase when they should be decreasing. This makes it harder to get to sleep.
如果在睡前吃得太快，你的代谢率和体温会在应该下降的时候上升，这会使人难以入睡。
Your body temperature dips at this time of day, just like it does before you go to bed at night.
这时你的体温下降，就像你晚上睡觉之前时一样。
Take a hot bath before bed. The drop in body temperature after the bath may help you feel sleepy, and the bath can help relax you.
睡前洗热水澡：洗澡后体温的下降会促进你睡觉，洗澡可以让你身心放松。
The temperature fell out of bed last night.
昨晚气温骤降。
Plastic mulch increases soil temperature in the bed which promotes faster crop development and earlier yields.
塑料薄膜覆盖提高苗床的土壤温度，促进作物较快发育并提早成熟。
应用推荐