保证使用塑料套保护钳位和形式。
Make sure to use plastic wrap to protect the clamps and forms.
二本文论述了有源钳位正激变换器的原理与设计。
The analysis and design of an active clamped forward converter is presented in this paper.
继电器IC 3断开，保护放大器和钳位二极管。
Relay IC3 opens, protecting the amplifier and clamping diodes.
输入信号的直流恢复是完成了与内部同步头钳位。
Input signal DC restoration is accomplished with an internal sync tip clamp.
详细阐述和分析了用于正激变换器的有源钳位拓扑。
An active clamped topology for forward converters is presented and analyzed in detail.
简单地发布三容易到达钳位，并且速度锁锎准备好行动。
Simply release the three easy to reach clamps and the Speed Lock CF is ready for action.
注意到，通过钳位二极管，电流峰值比带低电阻ssr更高。
Note that the peak current through clamping diodes can be rather high with low-on-resistance SSRs.
继而在四步模式下，研究了钳位电压和驱动电压对机构负位移的影响。
The influences of the clamping and driving voltages on the recession displacement were studied.
在钳位以后应用的地方在烤箱最小限度于四个小时在150到180度。
After the clamps are applied place in oven for a minimum of four hours at 150 to 180 degrees.
第一，在场效应晶体管关断期间钳位电压是800伏特，高于600伏特。
First, the clamping voltage during the MOSFETs turning off is 800V, what is higher then of 600V.
要确保输入端钳位电压足够的高，以避免由于源接点的非线性而产生的问题。
Make sure the compliance voltage is high enough to avoid problems due to source contact non-linearity.
在变压器的初级使用二极管钳位电路，可以有效地抑制变压器次级的寄生振荡。
And the diode clamp circuit introduced in the transformer primary can apparently restrain from the peak voltage resonance in the rectified diodes.
由于直流电压源的钳位作用，交流侧输出电压波形为矩形波，并且与负载阻抗角无关。
Because the clamp effect of DC voltage source, AC side output the rectangular wave voltage waveform, and it has nothing to do with the load impedance Angle.
为了及时了解压敏电阻的状态，研制了一种用于钳位型SPD带电检测的智能检测仪。
For detecting the state of varistor, an live detection device used in SPD detection is developed, which solves the automatic detecting problem about SPD detection on-line.
一个完美的结合，是适合时顶部钳位牢固下来都转向杆，把手，同时保持较低的铸造平行。
A perfect fit is when top clamp fits firmly down on both steering lever and handlebars while maintaining parallel with the lower casting.
符合人体工程学地被塑造的，高技术钳位有保证的一个被环绕的设计缆绳滑下，无需捉住。
The ergonomically shaped, high-tech clamps have a rounded design which ensures that cables slide off without catching.
该变换器电路结构上采用正激一零电流准谐振软开关电路拓扑结构，并结合了有源钳位技术；
This module uses a circuit topology of forward pulse width modulated - zero current quasi - resonance soft - switching , combined with active clamp technology.
此功能消除了在大多数应用中需要外部钳位二极管，节省了成本和外部元件数量，同时降低功耗。
This feature eliminates the need for external clamp diodes in most applications, saving cost and external component count, while minimizing power dissipation.
钳位电路用于某些数据设备可使接收器输出为常量，并且可在没有收到数据信号时避免噪音干扰。
A clamp is used in some data sets to hold receiver output constant and avoid troublesome noise interference when no data signals are being received.
然而，由于漏感影响，反激变换器功率开关管关断时将引起电压尖峰，必须用钳位电路加以抑制。
However, due to leakage effects flyback converter power switch off when the voltage spike caused by the need to be inhibited by clamping circuit.
利用有源钳位电路实现主变压器铁心对称复位，功率开关在宽输入电压和宽负载电流范围内零电压开关。
By using an active clamp circuit, the power transformer core is symmetrically reset. Zero voltage switching conditions are achieved over a broad input voltage and output current range.
这种离析主要原理的手法有助于合理审视电源电路里诸如变化速率、振荡、钳位、缓冲、反射电压等过程。
The separation into main elements should be done in respect of reasonable events in the power circuit like on and off slopes, oscillations, clamping, snubbering, reflected voltage, etc.
由于RCD钳位电路比有源钳位电路更简洁且易实现，因而在小功率变换场合RCD钳位更有实用价值。
RCD clamp circuit as a result of active-clamp circuit than the more concise and easy to realize, and in low-power transform RCD clamp occasions more practical value.
当使用者钳位开关到位置1时，管脚通过电阻r 5连接到VDD，管脚位为1，不论端口位是什么值。
When the user toggles the switch to Position 1, the pin connects to VDD through resistor R5, and the pin bit is one, regardless of the value of the port bit.
ECS普通电池连接功能，一个非常安全的包含钳位的设计，其中给电池标杆提供了一个老虎钳一样的位置。
ECS Universal battery Connector features an extremely secure clamping design which provides a vise-like grip on the battery post.
有源钳位z VS - PW M正激变换器可以适应这一发展趋势，因为它具有软开关和磁芯自动复位功能。
The active clamp ZVS-PWM forward converter has been answered for with the merits of the soft switch technique and the magnetic reset technique.
介绍了在二极管钳位三电平逆变器异步电机调速系统中如何采用空间矢量调制与直接转矩控制相结合的控制方法。
So this paper focuses on the study of direct torque control of induction motor based on diode-clamped three-level inverter.
举例说明，20兆赫兹的峰点是钳位过程结束后主要由场效应晶体管输出电容和变压器漏感引起的寄生振荡产生的。
For example, the peak at 20 MHz in the spectrum is caused by the parasitic oscillation due to the output capacitance of the MOSFET and the leakage inductance of the transformer.
举例说明，20兆赫兹的峰点是钳位过程结束后主要由场效应晶体管输出电容和变压器漏感引起的寄生振荡产生的。
For example, the peak at 20 MHz in the spectrum is caused by the parasitic oscillation due to the output capacitance of the MOSFET and the leakage inductance of the transformer.
应用推荐