弯曲强度是指材料在弯曲负荷作用下破裂或达到规定弯矩时能承受的最大应力，此应力为弯曲时的最大正应力，以MPa（兆帕）为单位。它反映了材料抗弯曲的能力，用来衡量材料的弯曲性能。
... 凝胶时间Gel Time min 弯曲强度Flexural Strength Mpa 固体含量Solid Content% ...
基于8个网页-相关网页
... bending strength弯曲强度；抗弯强度 bending moment弯矩；弯曲力矩；挠矩 bending machine[化]折弯机 ...
基于5个网页-相关网页
交变弯曲强度 alternate bending strength ; reversed bending strength
纵向弯曲强度 buckling strength
视弯曲强度 apparent bending stress ; apparentbendingstressormodulusofrupture
双轴弯曲强度 biaxial flexural strength
纵弯曲强度 buckling strength
抗弯曲强度 flexural strength ; bending resistance ; strength, flexural
极限弯曲强度 ultimate bending strength
垂直层向弯曲强度 Vertical Bending Strength
高温弯曲强度 high-temperature bending strength
At high temperature, bending strength of TiC-Ni cermets decreased with temperature increasing and plastic distortion took place beyond 1000℃.
随着温度的升高，TiC-Ni材料弯曲强度下降，温度超过1000℃开始发生塑性变形。
参考来源 - 燃烧合成TiCThe results of the mechanical property measurement showed that CaSO4 whisker could improve tensile strength and flexural strength of PP KPDM blend simultaneously. and that the composites with good rigidity and impact could he gotten hy controlling components.
力学性能测试结果表明,硫酸钙晶须可提高PP/EPDM基体的拉伸强度和弯曲强度,且通过控制各组分配比可制得韧性和刚度均衡的复合材料。
参考来源 - 硫酸钙晶须/PP/EPDM复合材料力学性能研究The gel time was 1.7h and the flexural strength and the compression strength could reach 74.6MPa and 58.2MPa respectively.
凝胶时间为1.7h,弯曲强度可达74.6MPa,压缩强度可达58.2MPa。
参考来源 - 曼尼希改性异佛尔酮二胺环氧固化剂性能研究Adding of LDPE causes the melt strength to grow but the stretching and bending strength to decrease.
低密度聚乙烯用量增加时，熔体强度会有所上升，但力学性能会下降。 总的说来，熔体强度高的产物冲击强度较高，但拉伸强度和弯曲强度有下降的倾向。
参考来源 - 高熔体强度聚丙烯的研究·2,447,543篇论文数据，部分数据来源于NoteExpress
弯曲强度显著增加200和400小时的老化只。
Bending strength significantly increased after 200 and 400 hours of aging only.
在侧向纤维方向的材料弯曲强度也可发现相同的趋势。
The similar tendency was also found in the transverse flexural strength of the composites.
研究表明制品在各流动方向上的弯曲强度有很显著的差别。
Results showed that the flexural strength of ESMC parts was different at different direction of fiber orientation.
应用推荐