研究了高锰奥氏体钢的低温断裂机制。
The low temperature fracture mechanism of high manganese austenitic steels is studied.
研究了铸造复合中锰奥氏体钢在冲击磨料磨损条件下的耐磨性能。
The wear resistance of casting composite medium manganese steel has been studied under the condition of impact abrasive wear.
研究了高锰奥氏体钢在77K下的抗拉性能、形变组织和断裂特点。
The tensile properties, deformed microstructure and fracture at 77K in high-Mn austenitic steels have been investigated.
结果表明：铸造复合中锰奥氏体钢的耐磨性是高锰钢的5.41倍。
The results show that the wear resistance of casting composite medium manganese steel is 5.41 times that of Hadfield steel.
高锰奥氏体钢随温度降低其断裂机制由韧窝状断裂转变到晶界断裂。
High manganese steels undergo a ductile to brittle transition at low temperature, which is accompanied by a change in the fracture mechanism from dimple fracture to intergranular fracture.
含氮奥氏体钢具有优良的抗弹性能，并优于传统马氏体钢的抗弹性能。
Nitrogen alloyed austenitic steels showed excellent ballistic property, higher than that of martensite steel.
研究了铬加入高锰奥氏体钢中后，原奥氏体高锰钢组织中出现的一种新相。
The austenite manganese steel when added to with Chromium element appears a new phase.
在系统研究结果的基础上，分析总结了低温奥氏体钢中合金元素的综合作用。
On the basis of systematical study, the comprehensive effects of alloying elements in cryogenic austenitic steels were analyzed.
这一关系的确立，为从微观角度研究奥氏体钢的蠕变损伤提供了一种判断依据。
The establishment of the relationship would provide us a new judging rule used in researching creep damage of austenite steel from the...
通过铸造表面合金化和复合变质处理，使中锰奥氏体钢的强度、韧性和表面硬度显著提高。
The strength, toughness and surface hardness of medium Manganese austenitic steel have been increased greatly by casting surface alloying and complex modification.
复合变质中锰奥氏体钢的冲击韧度、裂纹形成功和裂纹扩展功分别比原来提高了263%、288%和232%。
The impact toughness, crack forming energy and crack extension energy of complex modified medium manganese austenitic steel. Are increased by 263%? 288% and 232% respectively.
马氏体钢抗杆式模拟弹防护系数随着强度的提高而提高，呈线性关系，含氮奥氏体钢穿甲防护系数远远高于同一强度级别的马氏体钢。
For mass efficiency of penetration, martensite steel increases in line with strength, and nitrogen alloyed austenitic steel is much higher than that of the same strength martensite steel.
钢板应为全镇静钢且经奥氏体精细粒度处理。规格化的，规格化及回火的或淬火及回火。(译文请指正)。
The plates shall be fully killed and shall be fine austenitic grain treated. They shall be normalized, normalized and tempered or quenched and tempered.
介绍了一种改进的奥氏体不锈钢的双人双面同步钨极氩弧焊工艺。
This article mainly studies one kind improved two person two-sided synchronized GTAW process for the austenite stainless steel.
例如材料是奥氏体不锈钢。
Examples of such materials are: austenitic stainless steels.
在横轧前增加正火工序，改善钢的奥氏体晶粒度，消除混晶组织。
Normalization procedure was added before the transverse rolling for improving steel austenite grain fineness and removing mischcrystal structure.
同时探索出一种新的管线钢原奥氏体晶界腐蚀方法。
A new method for showing the prior austenite crystal boundary corrosion, of pipeline steel has been also supposed.
研究了碳、硅和铝合金元素对水雾化奥氏体不锈钢粉末烧结时的表面反应的影响。
This paper analyzes the influences of carbon, silicon and aluminium on the surface reaction when sintering austenite stainless steel powder.
研究了奥氏体不锈钢焊接接头在不同酸性介质中的腐蚀行为。
The corrosion behavior of austenite stainless steel weld joint in the different acidic medium was studied.
这些是适用于高温应用环境的奥氏体不锈钢阀门的螺栓材料。
These are bolting materials suitable for high temperature service with austenitic stainless steel valve materials.
通过综合分析指出对流管发生失效的原因是奥氏体不锈钢长期在高温下工作引起的热脆化开裂。
Through the comprehensive analysis, the result shows that crack failure reason is embrittlement of the austenite stainless steel at high temperature.
超级奥氏体不锈钢的概念是与超级铁素体不锈钢及超级双相不锈钢一起出现的。
The concept of super austenitic stainless steel appeared with super ferrite stainless steel and super double phases stainless steel together.
本文讨论和分析了18 - 8奥氏体不锈钢接头晶间腐蚀问题，提出了相应的控制措施。
The article discussed and analysed 18-8 Austenite stainless steel joint question about Intercrystalline Corrosion, then it put forward appropriate measurements.
本文介绍了电刷镀技术在奥氏体不锈钢零部件表面损伤修复中的应用，提出了电刷镀修复奥氏体不锈钢件的工艺流程及条件。
In this paper the application of the brush plating technology in mending surface damage of Austenite stainless steel parts is introduced. The process and conditions of this technology are put forward.
固溶处理是改善和提高奥氏体不锈钢波纹管抗应力腐蚀能力的有效措施。
And solution treatment is the valid method to improve the anticorrosion property of the austenite stainless steel bellows.
研究了碳、硅和铝合金元素对水雾化奥氏体不锈钢粉末烧结时的表面反应的影响。
Influences of carbon, silicon and aluminium on the surface reaction of austenite stainless steel powder during sintering have been studied.
研究了碳、硅和铝合金元素对水雾化奥氏体不锈钢粉末烧结时的表面反应的影响。
Influences of carbon, silicon and aluminium on the surface reaction of austenite stainless steel powder during sintering have been studied.
应用推荐