热流密度(Heat Flux,Thermal Flux),也称热通量,一般用q表示,定义为:单位时间内,通过物体单位横截面积上的热量。按照国际单位制,时间为s,面积为㎡,热量取单位为焦耳(J),相应地热流密度单位为J/㎡·s。
...整个换热器的传热速率 表征了换热器的生产能力,单位为W; q=Q/A 2 、热通量q (heat flux)或热流密度(density of heat flow rate) 指单位时间内通过单位传热面积缩传递的热量。在一定的 传热速率下,q越大,所需的传热面积越小。
基于364个网页-相关网页
...第一章 绪论 1、热流量(heat transfer rate):单位时间内通过某一给定面积的热量 2、热流密度(heat flux):通过单位面积的热流量。
基于154个网页-相关网页
高铝TRIP钢连铸过程中保护渣中Al 关键字: Al-TRIP钢;结晶器保护渣;Al2O3;热流密度[gap=1238]Key words: Al-TRIP steel; mold fluxes; Al2O3; heat flux density
基于154个网页-相关网页
... conductive heat flux 传导热通量 DNB heat flux DNB 热流密度 constant heat flux 恒定热流密度 ; 热通量 ...
基于26个网页-相关网页
临界热流密度 critical heat flux ; chf ; critical heat flux density
表面热流密度 surface heat flux
燃料表面热流密度 fuel surface heat flux density
局部热流密度 local heat flux density ; local heat flux
对流型热流密度 convective heat flow
传导型热流密度 conductive heat flow
热流密度计 Multiple-point Heat Flow Meter
烧毁热流密度 burn-out heat flux
恒定热流密度 constant heat flux
Heating power,flow rate,temperature of outer tube wall and temperature of fluid were measured under constant heat flux.
在等热流密度加热条件下,测量出加热功率、流速、管壁和流体进出口温度。
参考来源 - 水合物浆体在直管中的流动换热特性研究The results of numerical analysis show that for a given channel, mass flux in the channel does exist a maximum, so does those of the experiment. There exists thermal drag in natural convective boiling.
结果给出:通道内自然对流沸腾存在热阻力;存在抽吸质量速度极大值,实测也证明了这一点;质量速度达到极值点以后,随热流密度增加,迅速下降,对应着第三类沸腾危机的发生,这为第三类沸腾危机提供了新的解释。
参考来源 - 窄通道内自然对流沸腾传热The experimental result indicated that the falling film heat transfer coefficient reduces,when the heat flow density increases in the condition of laminar falls.
实验结果表明,在层流降膜时,降膜传热系数随溶液进口浓度升高而减小,随热流密度增加而增大。
参考来源 - 不同浓度溴化锂溶液层流降膜传热性能实验研究Development of apparatus to test dynamic heat transmitting properties of fabrics. In this apparatus, the design program, testing basic frame and principal, acquired the experiment data by compute, determined the heater heat flux and sensors calibration are discussed.
在测试装置的设计思路、测试装置的基本结构、测试原理到数据采集程序的编制以及加热热流密度的确定、传感器的标定等方面进行了探讨与论述。
参考来源 - 织物热传递性能测试方法的研究·2,447,543篇论文数据,部分数据来源于NoteExpress
接触角对临界热流密度有重要的影响。
喷雾冷却是一种高效的高热流密度散热方式。
Spray cooling is an efficient method for high heat flux removal.
截面平均换热系数则与质量流速、热流密度、质量干度和蒸发压力密切相关。
The perimeter averaged heat transfer coefficients depend on heat flux, mass flow rate, quality and saturated pressure.
应用推荐