抗拉强度(tensile strength)是金属由均匀塑性形变向局部集中塑性变形过渡的临界值,也是金属在静拉伸条件下的最大承载能力。抗拉强度即表征材料最大均匀塑性变形的抗力,拉伸试样在承受最大拉应力之前,变形是均匀一致的,但超出之后,金属开始出现缩颈现象,即产生集中变形;对于没有(或很小)均匀塑性变形的脆性材料,它反映了材料的断裂抗力。符号为Rm(GB/T 228-1987旧国标规定抗拉强度符号为σb),单位为MPa。
抗拉强度:抗拉强度(tensile strength)是金属由均匀塑性变形向局部集中塑性变形过渡的临界值,也是金属在静拉伸条件下的最大承载能力。
基于4847个网页-相关网页
... 有的金属材料的屈服点极不明显,在测量上有困难,因此为了衡量材料的屈服特性,规定产生永久残余塑性变形等于一定值(一般为原长度的0.2%)时的应力,称为条件屈服强度或简称屈服强度σ0.2 。 抗拉强度(σb) 伸长率(δs) ...
基于1010个网页-相关网页
极限抗拉强度 [力] ultimate tensile strength ; UTS
轴向抗拉强度 axial tensile strength
抗拉强度试样 tensile test piece
劈裂抗拉强度 tensile splitting strength ; splitting tensile strength ; Splitting strength
抗拉强度试验 tensile strength test ; Test for tensile strength
单轴抗拉强度 uniaxial tension test ; uniaxial tensile strength
钢丝抗拉强度 [力] tensile strength of wire
抗拉强度增大 increase of tensile strength
抗拉强度. Tensile Strength
The test results indicated that the bond splitting tensile strength of modified fly ash mortar was best in joint materials of sorts.
试验结果表明,各种接缝面材料中,粉煤灰改性砂浆的劈裂抗拉强度最大,效果最好。
参考来源 - 混凝土施工缝接缝面劈拉强度试验研究The tensile strength of specimens containing fibers of 0.35 volume fraction reaches up to 1050MPa.
试样的抗拉强度在纤维体积分数为0.35时达1050MPa。
参考来源 - 真空铸造高强度C/Mg复合材料Comparing to other structure shape, this form exerts tension strength of steel and compression strength of concrete much more. And it has many advantages, such as: legerity, slinky, big span ability, celerity construct, good traffic when constructing and so on.
相对于其它的一些结构形式,钢箱—混凝土组合梁充分发挥了钢材的抗拉强度与混凝土的抗压强度(尤其是简支组合梁桥这一优点更为突出),具有结构轻巧美观、跨越能力大、施工快速方便、不中断现况交通等优点。
参考来源 - 大跨径钢—混凝土连续组合梁桥设计研究·2,447,543篇论文数据,部分数据来源于NoteExpress
最近开发的一种新材料的抗拉强度比钻石还高,而且柔韧性更好。
A new material developed recently has a tensile strength higher than diamond, yet it's much more flexible.
该理论于19世纪末首次提出,其依据是水的抗拉强度,而水的这种特性通常与流体无关。
First proposed in the late 1800s, the theory relies on a property of water not commonly associated with fluids: its tensile strength.
他们也有更多的抗拉强度和延性较低。
应用推荐