目的探索建立无血预充兔体外循环模型的方法。
Objective To establish a rabbit model of the cardiopulmonary bypass (CPB) flushed without blood.
本公司是目前国内最大的预充式注射器流水线制造厂商。
Our company is the largest manufacturer of Pre-filled syringe production lines.
目的探讨儿童心脏手术中不同预充方法对围术期恢复的影响。
OBJECTIVE To investigate the the effect of different priming methods on the cardiopulmonary bypass (CPB) quality change and perioperative recovery.
对预充式注射剂车间工艺以及主要生产设备作了简要的论述。
The process of pre-filling injection agent workshop and main equipment used in production were briefly introduced in this article.
目的：观察体外循环中预充血定安对预充液胶体渗透压的影响。
Objective:To observe the effect of Gelofusine for colloid osmosis pressure(COP) during cardiopulmonary bypass.
用两种最大呼吸和潮气量技术进行全氧摄取：预充氧的生理学研究。
Total Oxygen Uptake with Two Maximal Breathing Techniques and Tidal Volume Breathing Technique: A Physiological Study of Preoxygenation Pandit JJ, et al.
针对水平井成井特点，结合大量室内试验，研制了双壁预充陶粒携砾过滤器。
Aimed at the characteristic of horizontal well, combined with large amount of laboratory tests, double-wall pre-packed gravel screen is developed.
目的研究晶体或胶体预充对O型与非O型血剖宫产产妇血栓弹力图的影响。
Objective To study the effects of type O or non-O blood maternal thrombelastogram when preloading with colloid or crystalloid during Cesarean section.
有血预充、减少总预充量和维持足够的转流流量是建立大鼠体外循环模型的关键。
Blood priming, total priming reduction and enough bypass flow were the key points in establishing the CPB model in rats.
公司生产的预充式注射器灌装加塞设备涵盖了低速、高速，真空与非真空诸多品种。
The Pre-filled syringe filling & stoppering machines are available in many types such as low speed, high speed, vacuum, non-vacuum, etc.
目的比较不同预充基础液勃脉力-A和乳酸林格氏液在小儿心脏病手术中的使用结果。
OBJECTIVE The objective of this study is to compare the effects of Plasmalyte-A and Lactate Ringer's as priming solution in pediatric open heart surgery.
分析了实现在线浓缩取样的关键技术，研究了蓄能器预充压力和采样筒保压效果的关系。
Key techniques of on-line concentrated sampling are analyzed and relations of accumulator precharge pressure and pressure-retaining results are studied.
目的探讨6%中分子羟乙基淀粉和4%琥珀明胶用于体外循环预充对患者肺功能的影响。
OBJECTIVE To observe the effect of 6% hydroxyethyl starch(HES) and 4% succinylated gelatin(GEL) for priming on lung function in the operation with extracorporeal circulation.
如果不考虑伪路径的影响，求值方向和预充方向延时的最大误差分别为3.62%和8.26%。
Without false paths, the errors of evaluation delay and precharge delay are within 3.62% and 8.26% respectively.
针对两种采用不同灰度调制方式和预充方法的新型无源OLED显示列驱动电路进行研究和设计。
The paper presents two novel PM-OLED column driver circuits with different grayscale modulation methods and pre-charge methods.
准均质充量压缩点火燃烧(QHCCI)方式占总燃料多数的预混合燃料以稀薄燃烧完成，故可能有很低的排放，尤其是碳烟和氮氧化物。
Quasi homogeneous charge compression ignition (QHCCI) combustion may be with low emissions, especially for soot and NO_X, according as the most fuel which is pre-mixed is lean burnt.
通过改进预锻模膛的设计，利用镦粗成型、反挤成型的原理，有效解决了130转向节板部模锻成型时充不满的问题。
By improving the design of forging die and using press-forging and backward extrusion principle, solves the problems of 130 steering knuckle forming which can not be fully filled during forming.
该工艺通过向气囊内充压，对预成型体施加一定的成型压力，从而提高构件纤维体积含量及力学性能。
This process can add mould pressure to the preforms through inflating the bladder. Thus, higher fiber volume fraction can be achieved.
考察熔体注射温度、注射时间、入口位置、材料性质对充模过程的影响，得到优化充模结果；还考察了气体辅助注塑过程熔体预注射量、气体注射压力对充模过程的影响。
The influences of melt injection temperature, injection time, gate location and materials property on the filling process were studied and the reasonable results were attained.
还考察了气体辅助注塑过程熔体预注射量、气体注射压力对充模过程的影响。
And also, the influences of pre-injected resin volume and gas pressure on gas-assisted...
还考察了气体辅助注塑过程熔体预注射量、气体注射压力对充模过程的影响。
And also, the influences of pre-injected resin volume and gas pressure on gas-assisted...
应用推荐