按“-键”画面自动下行到零点校正位并停止运行。
Press "-", and the image will automatically run down to the zero-point calibration position and then stop.
该方法可以在对移相器零点校正同时进行移相器相序检验，方法简单，具有实用价值。
This method can test phase sequence of phase switcher while rectifying the zero point of phase switcher. This method is simple and value in practice.
最后，在完成每次取样和净化顺序后，必须借助于水游离度测量来校正测量仪器的零点，以确保可以进行下一个读数。
Finally, after each sampling and cleaning sequence the measurements’ zero point ischecked with a water freeness measurement to make sure the next reading isrepeatable.
采用水柱校正法对差压传感器的零点及线性特性进行校正以保证高精度的差压数据。
The zero and linearity characteristic of differential pressure transducer is corrected with method of water column correction to ensure higher precision differential pressure data.
对所有多聚体分子间相互作用能的计算，进行基组叠加误差（BSSE）和零点能（ZPE）校正都是必要的。
The basis set superposition error (BSSE) and zero point energies (ZPE) corrections are absolutely necessary for the interaction energies of the clusters.
经过零点能校正后能位面被作了出来。
The potential energy surface with zero-point energy correction is drawn.
该系统能对压力传感器的零点误差、灵敏度误差和温度漂移进行自动的补偿校正。
The system can automatically compensate and calibrate the pressure sensor's zero point error, sensitivity error and thermal drift.
在各基组下均进行基组叠加误差(BSSE)和零点能(ZPE)校正求得结合能。
All the binding energies have been corrected by the basis set superposition error (BSSE) and zero point energies (ZPE).
解离能计算进行了零点振动能(ZPVE)校正，并运用完全均衡校正法对基函数重叠误差(BSSE)进行校正。
For dissociation energy, zero point vibration energy (ZPVE) is calculated and basis set superposition error (BSSE) is corrected by counterpoise method.
对于单点能采用零点能校正。
经MP2电子相关和基组叠加误差（BSSE）以及零点能（ZPE）校正，求得分子间相互作用能；
The intermolecular interaction energy is calculated with MP2 electron correlation correction, basis set superposition error (BSSE) correction and zero point energy (ZPE) correction.
软件校准测量电路的零点和满度，软件校正温度传感器和测量电路的非线性。
The method of software is applied to calibrate zero and full scale of the circuit and nonlinear approach for sensor and circuit.
输出零点和输出满度校正。
在控制方案上采用速度控制和张力控制的复合控制方式，同时通过软硬件对张力测定仪的零点漂移进行补偿和现场校正。
The compound control mode of speed control and tension control was used and the zero shift of the tension measuring device was compensated and spot-calibrated by software and hardware.
重力资料内业整理包括零点位移校正、正常场改正、厄特渥斯校正、布格改正及格莱尼异常改正等。
The gravity data processing includes displacement rectification, normal field correction, Eotvos rectification, Bouguer correction and Grany anomaly correction.
此方法根据线性校正算法给每个探测单元以相应的校正参数，然后通过增益控制电路和零点补偿电路来调整最终的输出。
Correction parameters corresponding to each individual detector are computed by linear correction algorithm. Then the gain control circuit and the offset compensation circuit adjust the final output.
此方法根据线性校正算法给每个探测单元以相应的校正参数，然后通过增益控制电路和零点补偿电路来调整最终的输出。
Correction parameters corresponding to each individual detector are computed by linear correction algorithm. Then the gain control circuit and the offset compensation circuit adjust the final output.
应用推荐