该方法考虑了不为零厚度的金属膜片及窗口槽的影响。
The influences of the nonzero metallization thickness and the mounting grooves are taken into account in the method.
本文在对钣金件特征研究和“零厚度”假设的基础上，提出了一种钣金件拓扑元素命名和辨别的新方法。
Based on the study of features of sheet metal parts and Zero Thickness Hypothesis, a new mechanism of naming and identifying topological entities of a feature model is proposed in this paper.
地表的冰厚度达到1米左右，最低温度为零下35摄氏度，但是因为有风寒，温度可降至零下70至80摄氏度左右。
There is about a metre of ice on the surface and the lowest temperature has been minus 35 degrees Centigrade but with the wind chill, it can go down to about minus 70-80c.
沉积速度：单位时间内零件表面沉积出金属的厚度。
Sedimentary speed: unit time parts deposition on the surface of the metal thickness.
减少施镀时间，降低镀层厚度，解决了镀层起泡脱皮质量问题，保证了化学镀镍零件的防腐性能。
Reducing plating time and coating thickness can solve these problems. So these methods can solve quality problem of the bubbling and...
对电镀产品镀前与镀后零件尺寸及公差、镀层厚度及公差之间的问题及关系进行了分析与探讨。
This paper analyzes and discusses the size, tolerance, width and the problems among tolerances of electroplate production before and after the plating.
夹钳系统能适合不同的厚度的工作，设有基准零位挡块，工件由滚球工作台支撑。
And the princer system can suit workpiece with different thickness and there is benchmark null position stop. The workpiece is supported by ball operation board.
该方法通过设计一系列的装配调试工装来代替弧齿锥齿轮和部分零件的位置，并据此测量和计算出所需调整垫片的厚度。
A series of assembly jigs were designed to take the place of spiral bevel gears and some parts, whereby the thickness of spacers was measured and calculated.
论证了在一定漆层厚度下带漆零件的涡流探伤的可行性。
It discusses the feasibility of eddy current testing of the parts with certain thickness of paint.
对于水动力噪声情况，感兴趣的频率厚度乘积相当低，这时零阶对称模式对噪声辐射起主要作用。
For the case of hydrodynamic noise, in which the range of the frequency-thickness product of interest is relatively low, the symmetric zero-order mode dominates the noise radiation.
这两艘船是专门为北冰洋地区的极端气候设计的，将在浮冰厚度达1.7米以及温度低至零下35摄氏度的环境中操作。
Designed for extreme environmental conditions in the arctic sea, the vessels will operate in drifting ice of up to 1.7 meters thick and temperatures as low as minus 35 degrees Celsius.
认为，板料零件数控渐进成形是使板料的厚度减薄，表面积增大，靠逐次的变形累积产生整体的变形。
Sheet thickness is thinned, surface area is increased in the nc incremental sheet metal parts forming process, and sheet forming point by point is to lead to the whole sheet deformation.
由于零件厚度薄、多向弯曲、回弹量大且相互影响，用常规回弹补偿法很难确定回弹规律。
Since the part is thin, multi-direction bending and springback is large, it is very difficult to decide the springback law using the usual compensation method.
在作大厚度切割时，变频跟踪应适当调慢，最好从零位起调至切割稳定，电流表指针不再激烈晃动。
When advancing large thickness cutting, frequency tracking shall be properly adjusted slow, you'd better adjust it to stable cutting from zero position and ammeter pointer no longer shakes sharply.
在该加载模式下，拉深件无起皱和拉裂缺陷，零件区域厚度分布均匀，整体成形质量较好，满足设计和使用要求。
In this mode, there is no wrinkle and crack in drawing parts, the thickness distribution is even and the overall forming quality is better, which meet the design and use requirements.
不同厚度、不同材料的零件可以在同一个模具上生产；
The different thickness, the different material's components may produce on the identical mold;
厚度可控。可用于修复零件表面和工模具因磨削加工或磨损而引起的尺寸超差，使报废零件复用。
Thickness could be controlled, it can beused to repair parts for the surface and tool grinding or wear caused by thedimension tolerance, so that can make the scrapped parts reuse.
利用位错形成能等于零(即错配应变能的降低等于位错自能)的条件，得到了外延生长薄膜的临界厚度。
The critical thickness is determined from the zero formation energy of a misfit dislocation. i. e. the amount of reduced mismatch strain energy equaling the amount of creased dislocation self energy.
超塑性胀形控制有各种方法，本文介绍了一种按气压与高度曲线控制的方法，使成形过程更接近于等应变速率胀形，能进一步改善零件厚度的不均匀性。
This paper introduces a method to controll a superplastic bulging by a gas-pressure and a height curve. This method can significantly reduce the thinning rate and unevenness of bulging material.
厚度可控。可用于修复零件表面和工模具因磨削加工或磨损而引起的尺寸超差，使报废零件复用。
Thickness could be controlled, it can be used to repair parts for the surface and tool grinding or wear caused by the dimension tolerance, so that can make the scrapped parts reuse.
厚度可控。可用于修复零件表面和工模具因磨削加工或磨损而引起的尺寸超差，使报废零件复用。
Thickness could be controlled, it can be used to repair parts for the surface and tool grinding or wear caused by the dimension tolerance, so that can make the scrapped parts reuse.
应用推荐