论文主要阐述了寻北仪中双阳极共阴极结构的激光陀螺高稳定度稳流电源的实现过程。
This paper mainly discusses how to design a high stability current control power supply for laser gyro of double anodes and common cathode in North-Finder based on Ring laser Gyroscope.
铝合金是一种理想的阳极材料，在化学电源和牺牲阳极方面已得到越来越广泛的应用。
Al alloy anode is an ideal metal material and is widely used in batter and sacrifice anode.
采用自制脉冲恒流电源，研究了缝纫机零部件（2A12）在低硫酸浓度下的脉冲恒流硬质阳极氧化工艺。
The hardened anodic oxidation coating on sewing machine components(2A12)was investigated in different sulfuric acid density solutions with special apparatus.
推荐了几种外加电源的阳极设置方案。
Several programs for anodes allocation of impressed current are recommended.
牺牲阳极法阴极保护因其不需电源、管理简单、电流分布均匀，特别是对于形状特殊的构筑物。
The sacrificial anode cathodic protection features no power source, simple management and even current distribution. It is well received especially on special shaped structure.
电源供电运行阴极之间的阳极通过钾肥，水的混合物，和一个“秘密催化剂”，并产生热量。
Mains electricity runs between a cathode to an anode through a mixture of potash, water, and a "secret catalyst", and generates heat.
硬质阳极化电源是对金属表面进行处理的装置。
Hard anodizing power supply is an important part of the equipment to deal with metal surface.
研究了一种采用双向脉冲电源将铝合金阳极氧化膜在硫酸铝溶液中进行封闭的绿色工艺。
A new pulse sealing treatment, involving the use of an asymmetric pulse power supply to seal the anodic film on an al substrate immersed in a solution of aluminum sulfate, has been developed.
光电倍增管的增益，是阳极输出电流和光电阴极中光电流的比值，直接关系到电源电压。
The gain of the PMT, that is the ratio of anode output current to the photoelectric current from the photocathode, is directly related to the supply voltage.
制定的阳极网接地电阻计算公式，为电源设备选型提供了依据。
The equation for the calculation of grounding of anode network is developed, which is the basis for the selection of power supply equipment.
针对阳极控制电源的输出脉冲宽度变化大的特点，采用串联固态开关控制阳极电压。
Since the output pulse width of the anode control power supply had varied greatly, the series-connected Insulated Gate Bipolar Transistors(IGBT) switch was applied to anode control power supply.
如果需要更换阳极棒，请先关闭热水器电源。
For replacing the anode, shut-off the power to the water heater.
结果表明：电源波形是钛合金阳极氧化着色过程的关键因素之一，选择脉冲直流电源可以获得较好的着色膜性能；
Electric wave form was one of the key factors in anodizing, and selecting pulse DC power enabled the oxidizing film to have good quality;
着重评述了交直流叠加，脉冲电流和交流电源在硬质阳极氧化研究中的进展情况。
The progress of hard anodizing investigation employing A. C. superimposed on D. C. , pulse current and alternating cu…
着重评述了交直流叠加，脉冲电流和交流电源在硬质阳极氧化研究中的进展情况。
The progress of hard anodizing investigation employing A. C. superimposed on D. C. , pulse current and alternating cu…
应用推荐